cover
Contact Name
Marzuki
Contact Email
marzuki@pnl.ac.id
Phone
+6285260462751
Journal Mail Official
jmst@pnl.ac.id
Editorial Address
Jurusan Teknik Mesin, Politeknik Negeri Lhokseumawe Jl. Banda Aceh - Medan Km. 280,3, Buketrata, LHOKSEUMAWE 24301, Provinsi Aceh Tel : (0645) 427 85 Fax : (0645) 427 85 Surat-e : jmst@pnl.ac.id
Location
Kota lhokseumawe,
Aceh
INDONESIA
Jurnal Mesin Sains Terapan
ISSN : -     EISSN : 25979140     DOI : Prefix 10.30811/jmst by Crossref
Jurnal Mesin Sains Terapan adalah publikasi ilmiah yang memuat hasil-hasil penelitian kolaboratif antara mahasiswa dan dosen dalam bidang teknik mesin dan sains terapan. Terbit dua kali dalam setahun, yaitu pada bulan Maret dan September, jurnal ini bertujuan untuk mengembangkan inovasi serta kontribusi ilmiah dalam berbagai topik seperti mekanika, manufaktur, pengelasan, dan pemeliharaan mesin, energi terbarukan, desain mesin, dan aplikasi sains terapan lainnya. Jurnal ini menjadi media dokumentasi dan berbagi pengetahuan yang bermanfaat bagi akademisi dan praktisi di bidangnya.
Articles 167 Documents
Uji kekuatan tarik sambungan las double lap joint pada material baja karbon sedang Willy Mirza; Samsul Bahri; Syamsuar Syamsuar; Nurlaili Nurlaili
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10469

Abstract

Welding is one of the most widely used metal joining methods in the manufacturing industry, where the quality of the welded joint is strongly influenced by process parameters, particularly welding current. This study aims to analyze the effect of Shielded Metal Arc Welding (SMAW) current on the tensile strength of double lap joint welds made from AISI 1050 medium-carbon steel. The welding process was carried out using 2.4 mm diameter E7016 electrodes at three current levels: 70 A, 85 A, and 100 A. After welding, the specimens were subjected to non-destructive testing (liquid penetrant testing) to detect surface defects, followed by tensile testing using a Universal Testing Machine (UTM) in accordance with the ASME Section IX standard. The results showed that all specimens were free from significant surface defects. Tensile testing revealed that the highest average tensile strength was achieved at a welding current of 70 A, reaching 62.97 kgf/mm², followed by 100 A with 56.61 kgf/mm², while the lowest value was obtained at 85 A with 55.73 kgf/mm². The welding current significantly affected the quality of the welded joints. Excessively low current resulted in unstable weld penetration, whereas excessively high current accelerated electrode melting, thereby reducing the bonding strength of the weld metal. Therefore, selecting an appropriate welding current is essential for producing high-quality welded joints, and the findings of this study may serve as a reference for determining optimal welding parameters for medium carbon steel.
Pabrikasi mesin injection molding skala laboratorium menggunakan sampah limbah plastik sebagai bahan baku Ryan Jeremy; Tino Hermanto; Iswandi Iswandi; Arya Rudi Nasution
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10480

Abstract

Plastic waste is one of the environmental problems that requires practical processing technology, particularly at laboratory scale. This study aims to fabricate and evaluate a laboratory-scale injection molding machine using waste High-Density Polyethylene (HDPE) as feedstock. The research employed an experimental engineering-design approach consisting of design, component preparation, fabrication, assembly, material preparation, machine testing, observation, and descriptive analysis. The fabricated machine uses a vertical construction with a manual hydraulic-jack pressing system and consists of a frame, heating system, barrel, nozzle, plunger, temperature-control system, and mold. Testing showed that the machine operated at 200–250 °C and required approximately 12 minutes to melt the HDPE material. The molten material flowed through the nozzle into the mold without jamming or leakage, indicating adequate injection performance. The molded products generally followed the mold geometry, although surface texture was not fully uniform, with smooth, rough, and mixed areas. The machine was fabricated during 11 May–28 July 2026 with a machine fabrication cost of Rp3,500,000 and a mold cost of Rp1,100,000. The results indicate that the machine is feasible as a low-cost laboratory tool for plastic-waste processing, while temperature distribution, cooling, and material-size uniformity require further improvement.
Analisa pengaruh variasi kecepatan potong dan kedalaman pemakanan pada proses bubut baja St.42 terhadap kekasaran permukaan Sumardi Sumardi; Mahmud Mahmud; Saifuddin Saifuddin
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10464

Abstract

The surface quality of lathe-machined workpieces is primarily governed by three cutting parameters: spindle speed, feed rate, and depth of cut, as the resulting surface roughness directly determines the functional quality of the machined component. Empirical observations indicate that achieving a favourable surface roughness in the turning process depends on the appropriate selection of cutting tool parameters, since the cutting tool constitutes one of the principal elements of the turning system alongside the machine tool and the workpiece itself, and exerts a significant influence on the resulting surface finish. This study aims to determine the surface roughness values and roughness grades of St.42 steel under varying spindle speeds and depths of cut during the turning process. Experiments were performed using a PL-1000 G lathe machine with ST 42 steel specimens, and surface roughness was measured using a Mitutoyo SJ-310 roughness tester. The results indicate that the optimum surface roughness value (Ra) at a spindle speed of 1020 rpm and a depth of cut of 0.2 mm was 3.573 µm, corresponding to roughness grade N8. At a spindle speed of 1800 rpm and a depth of cut of 0.4 mm, the optimum Ra value was 1.678 µm, corresponding to roughness grade N7. Meanwhile, at a spindle speed of 550 rpm and a depth of cut of 0.2 mm, the Ra value obtained was 3.925 µm, corresponding to roughness grade N8. Overall, the average surface roughness values obtained, in terms of Ra and roughness grade (N7 and N8), indicate that the machined surfaces fall within the fine-finish category for the turning process.
Analisis distribusi temperatur reaktor gasifikasi downdraft multi-stage berbasis kontainer menggunakan simulasi termal Alvin Indi Lazuardi; Trisma Jaya Saputra; Nur Hayati; Arif Rahman Saleh
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10458

Abstract

Coffee husk waste is a promising biomass resource for renewable energy production through gasification; however, its utilization remains relatively limited. This study aimed to design a container-based downdraft gasification reactor with a processing capacity of 50 kg/h and evaluate its thermal performance through temperature distribution analysis using SolidWorks Simulation. The reactor dimensions were determined based on stoichiometric calculations with an equivalence ratio (ER) of 0.3, resulting in a reactor diameter of 760 mm, a height of 1900 mm, a throat diameter of 234 mm, and a nozzle diameter of 34 mm. Thermal simulations were conducted under steady-state conditions using Stainless Steel (SS) 310S as the reactor material. The applied thermal loads were 269.651°C in the drying and pyrolysis zone, 759.150°C in the oxidation (throat) zone, 250.843°C in the reduction zone, and 140.045°C at the grate, with a natural convection boundary condition of 5 W/(m²·K). The results showed that the highest temperature of 759.150°C occurred in the throat region, while the maximum outer surface temperature reached approximately 59.566°C. The estimated convective heat loss to the surrounding environment was 0.78 kW, equivalent to only 0.31% of the biomass energy input, indicating that the selected SS 310S material and wall thickness configuration provided effective thermal insulation. These findings provide a practical reference for the design and thermal optimization of safe and efficient container-based biomass gasification reactors
Desain dan simulasi statik rangka alat sortir buah kopi Tegar Indarto; Nur Hayati; Arbye S. Arbye S.; Trisma Jaya Saputra; Arif Rahman Saleh
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10475

Abstract

Manual coffee cherry sorting has limitations in terms of capacity, consistency, and efficiency, making it necessary to develop a sorting machine with a strong, safe, corrosion-resistant, and cost-effective structure. This study aims to design the frame of a coffee cherry sorting machine and determine the most suitable materials for the frame and hopper through static structural simulation. The design was developed using SolidWorks, while the structural analysis was conducted using SolidWorks Simulation based on the Finite Element Analysis (FEA) method to evaluate the von Mises stress, displacement, and Factor of Safety (FOS). The simulation results indicate that Galvanized Steel is the most suitable material for the machine frame, as it provides safe structural performance with maximum stress below the material’s yield strength, low displacement, and Factor of Safety that satisfies engineering safety requirement. In addition, Galvanized Steel offers better corrosion resistance and material cost efficiency than the other evaluated materials. For the hopper, Stainless Steel 201 demonstrated the best performance, achieving an excellent structural strength and corrosion resistance for coffee cherry handling applications. Based on the static simulation and cost analysis, Galvanized Steel is recommended as the frame material, while Stainless Steel 201 is recommended as the hopper material because they provide the best balance of structural strength, safety, corrosion resistance, and cost efficiency
Analisis variasi suhu tempering terhadap nilai kekerasan dan struktur mikro baja AISI 1045 Muhammad Syakir Al Amin; Saifuddin Saifuddin; Murtadhahadi Murtadhahadi
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10418

Abstract

Penelitian ini bertujuan untuk menganalisis pengaruh variasi suhu tempering terhadap nilai kekerasan dan struktur mikro baja AISI 1045. Material terlebih dahulu diberi perlakuan hardening pada temperatur 900°C selama 2 jam, kemudian dilakukan quenching menggunakan oli SAE 40. Selanjutnya, proses tempering dilakukan pada temperatur 150°C, 250°C, dan 300°C dengan holding time 1 jam. Pengujian yang dilakukan meliputi pengujian kekerasan Vickers dan pengamatan struktur mikro menggunakan mikroskop optik. Hasil penelitian menunjukkan bahwa nilai kekerasan raw material sebesar 227 HV meningkat menjadi 395,80 HV setelah proses hardening karena terbentuknya struktur martensit. Setelah tempering, nilai kekerasan yang diperoleh berturut-turut sebesar 307,06 HV pada 150°C, 311,64 HV pada 250°C, dan 353,56 HV pada 300°C. Pengamatan struktur mikro menunjukkan bahwa raw material didominasi ferit dan perlit, sedangkan setelah hardening terbentuk martensit. Setelah tempering, struktur berubah menjadi tempered martensite dengan presipitasi karbida yang semakin merata dan struktur yang lebih homogen pada temperatur 300°C. Berdasarkan hasil tersebut, variasi temperatur tempering berpengaruh terhadap perubahan kekerasan dan struktur mikro baja AISI 1045. Tempering 300°C menghasilkan struktur tempered martensite yang lebih homogen dengan nilai kekerasan 353,56 HV. Hasil ini menunjukkan bahwa pengaturan suhu tempering penting untuk memperoleh keseimbangan antara kekerasan, kestabilan struktur, keuletan, dan ketangguhan material sesuai kebutuhan aplikasi di bidang teknik
Pengaruh Minyak Nabati Sebagai Media Quenching Terhadap Nilai Kekerasan dan Struktur Mikro Baja SUP9 muhammad khardawi; Adi Saputra Ismy; Fakhriza Fakhriza
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10610

Abstract

Penelitian ini bertujuan untuk mengetahui pengaruh penggunaan minyak nabati sebagai media quenching terhadap nilai kekerasan dan struktur mikro baja SUP9. Material baja SUP9 terlebih dahulu dilakukan proses hardening pada temperatur 850 °C dengan holding time selama 30 menit, kemudian didinginkan menggunakan tiga jenis media quenching, yaitu minyak jarak, minyak kelapa, dan minyak kelapa sawit. Pengujian kekerasan dilakukan menggunakan metode Micro Vickers, sedangkan pengamatan struktur mikro dilakukan untuk mengetahui perubahan fasa setelah proses quenching. Hasil penelitian menunjukkan bahwa nilai kekerasan awal baja SUP9 sebesar 420 HV meningkat setelah proses quenching. Nilai kekerasan tertinggi diperoleh menggunakan minyak jarak sebesar 858,23 HV, diikuti minyak kelapa sebesar 833,06 HV dan minyak kelapa sawit sebesar 811,20 HV. Struktur mikro awal berupa ferrit dan perlit berubah menjadi struktur yang didominasi martensit setelah quenching. Dengan demikian, jenis minyak nabati berpengaruh terhadap peningkatan kekerasan dan perubahan struktur mikro baja SUP9, dengan minyak jarak memberikan hasil paling efektif. Kata kunci: Baja SUP9, Quenching, Minyak Nabati, Kekerasan, Struktur Mikro, Martensit.