cover
Contact Name
Marzuki
Contact Email
marzuki@pnl.ac.id
Phone
+6285260462751
Journal Mail Official
jmst@pnl.ac.id
Editorial Address
Jurusan Teknik Mesin, Politeknik Negeri Lhokseumawe Jl. Banda Aceh - Medan Km. 280,3, Buketrata, LHOKSEUMAWE 24301, Provinsi Aceh Tel : (0645) 427 85 Fax : (0645) 427 85 Surat-e : jmst@pnl.ac.id
Location
Kota lhokseumawe,
Aceh
INDONESIA
Jurnal Mesin Sains Terapan
ISSN : -     EISSN : 25979140     DOI : Prefix 10.30811/jmst by Crossref
Jurnal Mesin Sains Terapan adalah publikasi ilmiah yang memuat hasil-hasil penelitian kolaboratif antara mahasiswa dan dosen dalam bidang teknik mesin dan sains terapan. Terbit dua kali dalam setahun, yaitu pada bulan Maret dan September, jurnal ini bertujuan untuk mengembangkan inovasi serta kontribusi ilmiah dalam berbagai topik seperti mekanika, manufaktur, pengelasan, dan pemeliharaan mesin, energi terbarukan, desain mesin, dan aplikasi sains terapan lainnya. Jurnal ini menjadi media dokumentasi dan berbagi pengetahuan yang bermanfaat bagi akademisi dan praktisi di bidangnya.
Articles 167 Documents
Karakterisasi wet scrubber ekstrak cangkang kerang hijau terhadap penyerapan gas asam menggunakan simulasi CFD Pebri Akhrus Mahrun; Sigit Mujiarto; Arif Rahman Saleh; Rany Puspita Dewi
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10467

Abstract

The increasing use of incinerators as a waste treatment technology has resulted in the emission of acidic gases, including sulfur dioxide (SO₂), hydrogen chloride (HCl), and hydrogen fluoride (HF), which pose significant risks to environmental quality and public health. This study aimed to characterize the performance of a wet scrubber using calcium carbonate (CaCO₃) derived from green mussel (Perna viridis) shells as a natural absorbent for acid gas removal through Computational Fluid Dynamics (CFD) simulation. The simulation was performed using ANSYS Fluent with the species transport model and stoichiometric reactions between CaCO₃ and SO₂, HF, and HCl. The inlet gas concentrations were set at 23.65 mg/Nm³ for SO₂, 0.58 mg/Nm³ for HF, and 16.90 mg/Nm³ for HCl. The scrubber performance was evaluated based on the reduction in outlet gas concentrations and removal efficiency. The simulation results showed that the SO₂ concentration decreased to 13.06 mg/Nm³ with a removal efficiency of 44.80%, HF decreased to 0.32 mg/Nm³ with a removal efficiency of 44.80%, and HCl decreased to 9.33 mg/Nm³ with a removal efficiency of 44.43%. These reductions were attributed to the absorption process followed by neutralization reactions between the acidic gases and CaCO₃, producing more stable compounds. The findings demonstrate that a wet scrubber employing CaCO₃ derived from green mussel shells has considerable potential as an environmentally friendly natural absorbent for controlling acid gas emissions from incinerator flue gas.
Pengaruh variasi tekanan penyemprotan coating epoxy aluminium pada baja SS400 terhadap kekuatan adhesi dan ketebalan lapisan Muhammad Nur Falakh; Xander Salahudin; R. Faiz Listyanda
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10478

Abstract

SS400 steel is widely used in industry, but its surface is prone to quality degradation and therefore requires a protective coating with good adhesion strength, while spray pressure variation is known to affect coating quality. Studies on the effect of spray pressure variation on the adhesion strength and coating thickness of aluminum epoxy coating on SS400 steel are still limited. This study aims to analyze the effect of spray pressure variation (3, 4, and 5 bar) on adhesion strength and coating thickness on SS400 steel. An experimental method was used: SS400 steel specimens were first sandblasted and then coated with aluminum epoxy coating at each pressure variation, followed by testing using a pull-off test (ASTM D4541) for adhesion strength and a dry film thickness gauge for coating thickness. The results showed that the highest adhesion strength was obtained at 3 bar, amounting to 9.47 MPa, then decreased to 8.86 MPa at 4 bar and 8.61 MPa at 5 bar. Coating thickness showed a similar decreasing trend, from 73.7 μm at 3 bar to 73.4 μm at 4 bar and 72.9 μm at 5 bar. Overall, a spray pressure of 3 bar was the optimum parameter because it produced both the highest adhesion strength and the highest coating thickness among the three pressure variations tested
Rancang bangun alat uji impak komposit untuk karakterisasi bio-komposit berbasis limbah alam Ismi Amalia; Indra Mawardi; Sariyusda Sariyusda; Mawardi Mawardi; Meisi Andayani
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10461

Abstract

Impact toughness characterization is an important step in bio-composite development, yet the limited availability of affordable and reliable testing equipment remains a major challenge for many laboratories. This study presents the design, fabrication, calibration, and validation of a Charpy impact tester based on ASTM D6110 for laboratory-scale bio-composite characterization. The developed system demonstrated stable and consistent performance during calibration, confirming the reliability of its swing mechanism and measurement accuracy. Validation using five hybrid bio-composite variations showed that the tester consistently differentiated impact toughness, with absorbed energy increasing from 0.33 J in unreinforced specimens to 2.40 J in composites reinforced with three layers of mensiang fiber. By integrating mechanical design, fabrication, calibration, and validation into a single platform, the developed tester provides a reliable, economical, and practical alternative for independent bio-composite impact characterization.
Perancangan konseptual dan analisis termal water tube boiler berbasis pemanfaatan panas insinerator Umam Nashrullah; Nurmala Dyah Fajarningrum; Sigit Mujiarto
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10473

Abstract

National waste generation continues to increase each year, and a large proportion remains inadequately managed. One applicable treatment alternative is thermal processing using an incinerator, which produces heat energy that can potentially be utilized as an energy source for a boiler to generate steam. This study aims to obtain a conceptual design of a water tube boiler integrated with an incinerator with a capacity of 100 kg/h and to evaluate its structural strength through Finite Element Analysis (FEA)-based simulation. The methods used include energy balance calculation, heat transfer analysis, determination of the main dimensions, geometric modeling, and static structural simulation using SolidWorks software, with AISI 304 material and an operating pressure of 4 bar. The calculation results show that the available combustion heat energy is 680,000 kJ/h, with the boiler capacity set at 40 kg/h. The required heat transfer area is met using five heating tubes with a natural circulation system, and the maximum allowable working pressure (MAWP) is 1.156 MPa. The simulation results show a maximum von Mises Stress of 71.248 MPa at the junction between the drum and the water pipe, a maximum displacement of 0.217 mm, and a minimum Factor of Safety of 2.903, indicating that the structure is able to withstand the operating pressure. Based on the design and simulation results, the designed water tube boiler meets the specified capacity requirement and has adequate structural strength.
Pengaruh parameter suhu dan equivalence ratio terhadap kandungan tar pada gasifikasi limbah biomassa menggunakan ASPEN plus Nurbaity Khoirun Nissa; Arif Rahman Saleh; Arbye S Arbye S; Sigit Mujiarto
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10484

Abstract

Indonesia faces challenges in the transition toward cleaner and more sustainable energy, one of which is the utilization of rice husk biomass waste. Magelang Regency produces approximately 33,960 – 39,054 tons of rice husk per year, which has not been optimally utilized. Rice husk can be converted into synthesis gas through gasification, although this process produces tar that can clog equipment, cause corrosion, and reduce system efficiency. This study models the rice husk gasification process using ASPEN Plus software with a kinetic reaction approach at an operating temperature of 900°C, identified as the optimum temperature, and analyzes the effect of equivalence ratio (0.30, 0.35, and 0.40) on tar content and synthesis gas composition. The reactor model was developed through a drying stage using an RStoic block, pyrolysis using RYield and RGibbs blocks, and gasification using RPlug blocks divided into oxidation and reduction zones. The results show that increasing the equivalence ratio from 0.30 to 0.40 effectively reduces tar content from 0.03109 kg/Nm³ to 0.01206 kg/Nm³, while H2 content decreases from 14.01% to 11.66%, CO from 23.54% to 18.70%, and CH4 from 1.04% to 0.86%, whereas CO2 content increases from 5.95% to 8.23%. The condition of equivalence ratio 0.30 produced the best synthesis gas quality, while the lowest tar content was achieved at equivalence ratio 0.40.
Rancang bangun alat pengujian mesin alat berat pasca general overhaul Abyan Azra Dyanusa; Raka Mahendra Sulistiyo; Dimas Ardiansyah Halim; Herru Budi Santosa
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10468

Abstract

Heavy equipment engines require post-general overhaul functional testing to verify compliance with manufacturer specifications. Observations at a heavy equipment distribution and after-sales service company revealed that the testing process still relies on separate measuring instruments, resulting in longer testing time and increased operator exposure to running engines. This study designed an integrated engine testing device capable of displaying engine speed (RPM), oil pressure, and coolant temperature in real time through a single control panel. The system was developed using Autodesk Inventor for mechanical design and Autodesk Eagle for electrical wiring, followed by manufacturing and functional testing on a wheel loader engine based on the Komatsu shop manual. The test results showed a low idle speed of 820 rpm, a high idle speed of 2240 rpm, an oil pressure of 3.4 bar, and a coolant temperature of 82°C, all within the specified standards. The testing time decreased from 80 to 55 minutes (41.7% improvement), while eliminating manual harness installation and reducing operator exposure to hazardous areas. The proposed device improves the efficiency, accuracy, and safety of post-general overhaul engine testing.
Pengendalian korosi menggunakan green inhibitor pada baja karbon ASTM A53 Zaki Aufa Fahrezi; Nani Mulyaningsih; Agung Purnomo
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10479

Abstract

Corrosion is a major problem in ASTM A53 carbon steel, which is widely used in piping systems, making environmentally friendly corrosion control methods essential. This study aimed to analyze the effect of varying concentrations of waste tea (Camellia sinensis) extract as a green corrosion inhibitor on the corrosion rate of ASTM A53 carbon steel. An experimental method was employed using inhibitor concentrations of 0, 200, 400, and 600 mg/L in rainwater as the corrosive medium for an immersion period of five days. Corrosion testing was conducted using the potentiodynamic polarization method based on ASTM G102 to determine the corrosion rate. The results showed that the addition of waste tea extract significantly improved the corrosion resistance of carbon steel. The optimum performance was achieved at an inhibitor concentration of 600 mg/L, resulting in the lowest corrosion rate of 0.19149 mmpy and an inhibition efficiency of 77.31%, while the specimen without inhibitor exhibited the highest corrosion rate of 0.84407 mmpy. The formation of a more homogeneous adsorption layer effectively reduced the corrosion products on the steel surface. Therefore, waste tea extract has strong potential as an effective, economical, and environmentally friendly green corrosion inhibitor for protecting carbon steel piping systems.
Analisis kekuatan struktur pressure vessel penyimpanan syngas menggunakan finite element analysis (FEA) pada tekanan 35 bar Wahyu Tri Apriliyan; Sigit Mujiarto; Rany Puspita Dewi; Arif Rahman Saleh
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10462

Abstract

Synthetic gas (syngas) is a gaseous product of biomass gasification primarily composed of hydrogen (H₂) and carbon monoxide (CO), making it a promising alternative energy source. However, the flammable and toxic nature of syngas requires a safe and efficient storage system. This study aims to analyze the structural strength of an Adsorbed Natural Gas (ANG)-based pressure vessel for syngas storage at an operating pressure of 35 bar using the Finite Element Analysis (FEA) method. The pressure vessel was designed in accordance with the ASME BPVC Section VIII Division 1 standard, while the numerical simulation was performed using SolidWorks 2022. The design resulted in a horizontal pressure vessel with an internal diameter of 1.26 m and shell and head thicknesses of 36 mm. The simulation results indicated a maximum von Mises stress of 116 MPa, a maximum displacement of 0.705 mm, and a factor of safety of 2.2. The maximum stress remained below the yield strength of SA516 Grade 70 steel, indicating that the pressure vessel design is structurally safe and suitable for operation at a pressure of 35 bar.
Pengaruh variasi desain permukaan velocity stack terhadap daya dan torsi berbasis dynotest Muhammad Irdan Adhaqiqi; Trisma Jaya Saputra; Achmad Aziizudin
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10474

Abstract

Engine performance enhancement is typically achieved by modifying internal components; however, such methods entail higher costs and may compromise engine reliability. This study aims to analyze the effect of varying velocity stack surface designs on the power and torque of a standard 150 cc Yamaha Vixion engine. The velocity stacks were fabricated from PLA using 3D printing, featuring a length of 37 mm, an inclination angle of 10°, and three surface variations: smooth, dimpled, and spiral. Airflow characteristics were analyzed using Computational Fluid Dynamics (CFD) via Ansys Fluent, while performance testing was conducted using a dynamometer. The results indicate that velocity stack surface variations influence engine power and torque characteristics. The smooth velocity stack yielded the highest peak power of 15.62 hp at 8,230 rpm, whereas the dimpled velocity stack produced the highest peak torque of 14.17 Nm at 7,290 rpm. In addition to increasing power and torque compared to the standard velocity stack, the surface variations shifted the peak power and torque points to higher engine speeds. The CFD results corroborate the dynamometer test findings by demonstrating distinct airflow characteristics for each velocity stack design.
Perancangan dan analisis termal tabung pemanas berbasis heat exchanger coil menggunakan refrigeran R32 untuk sistem water jacket bioreaktor fermentasi kopi Bariq Firmanda; Trisma Jaya Saputra; Nur Hayati; Arif Rahman Saleh
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10485

Abstract

Temperature control is a crucial factor in the coffee fermentation process, as it influences both microbial activity and the quality of the final product. This study aimed to design a heating unit based on a shell-and-coil heat exchanger, utilizing R32 refrigerant as the heat source for the water jacket system of a coffee fermentation bioreactor. The design was developed using the Log Mean Temperature Difference (LMTD) method and subsequently validated through Computational Fluid Dynamics (CFD) simulation using ANSYS Fluent. Calculations yielded a heating unit with a capacity of 137.4 L, a coil length of 22.02 m, and a heat transfer rate of 1,354 W. Simulation results showed the water temperature rising from 27°C to 48°C, while the refrigerant temperature dropped from 90°C to 69.9°C. The simulation results differed from the theoretical values by approximately 2°C, indicating that the design effectively meets the heating requirements of the water jacket system. This research demonstrates that utilizing heat from an air conditioner condenser with R32 refrigerant offers a potential alternative for an efficient heating system in coffee fermentation bioreactors.