cover
Contact Name
Marzuki
Contact Email
marzuki@pnl.ac.id
Phone
+6285260462751
Journal Mail Official
jmst@pnl.ac.id
Editorial Address
Jurusan Teknik Mesin, Politeknik Negeri Lhokseumawe Jl. Banda Aceh - Medan Km. 280,3, Buketrata, LHOKSEUMAWE 24301, Provinsi Aceh Tel : (0645) 427 85 Fax : (0645) 427 85 Surat-e : jmst@pnl.ac.id
Location
Kota lhokseumawe,
Aceh
INDONESIA
Jurnal Mesin Sains Terapan
ISSN : -     EISSN : 25979140     DOI : Prefix 10.30811/jmst by Crossref
Jurnal Mesin Sains Terapan adalah publikasi ilmiah yang memuat hasil-hasil penelitian kolaboratif antara mahasiswa dan dosen dalam bidang teknik mesin dan sains terapan. Terbit dua kali dalam setahun, yaitu pada bulan Maret dan September, jurnal ini bertujuan untuk mengembangkan inovasi serta kontribusi ilmiah dalam berbagai topik seperti mekanika, manufaktur, pengelasan, dan pemeliharaan mesin, energi terbarukan, desain mesin, dan aplikasi sains terapan lainnya. Jurnal ini menjadi media dokumentasi dan berbagi pengetahuan yang bermanfaat bagi akademisi dan praktisi di bidangnya.
Articles 167 Documents
Inspeksi cacat las pengelasan SMAW pada pipa baja karbon ASTM A106 grade B Chairul Fahmi; Hamdani Hamdani; Al Fathier Al Fathier
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10465

Abstract

Shielded Metal Arc Welding (SMAW) is one of the most widely used welding processes for carbon steel piping due to its simplicity, cost-effectiveness, and reliability. However, welding defects may reduce joint integrity and compromise structural safety. This study aims to evaluate the surface quality of SMAW welded ASTM A106 Grade B pipe using Liquid Penetrant Testing (LPT), a non-destructive testing (NDT) method for detecting surface-breaking discontinuities. Pipe specimens with a diameter of 6 inches and a thickness of 6 mm were welded in the 5G position using E6010 electrodes for the root pass and E7018 electrodes for the fill and cap passes. The welded joints were visually inspected and subsequently examined using liquid penetrant testing at eight inspection locations before and after machining. The results showed that E6010 provided adequate root penetration, while E7018 produced smoother weld beads. The predominant surface defects identified were porosity, slag inclusion, and spatter. Machining reduced the number of detectable surface defects in most inspection areas, indicating the removal of superficial imperfections. Furthermore, appropriate selection of welding parameters, particularly welding current and electrode type, contributed to improved weld quality. The study demonstrates that liquid penetrant testing is an effective and practical technique for evaluating the surface integrity of SMAW welded ASTM A106 Grade B pipes and supports quality assurance in industrial welding applications
Analisis kerusakan blade low pressure turbin PLTU Nagan Raya menggunakan metode RCA Mokhamad Gilang Yuniar Rizki; Hamdani Hamdani; Muhammad Razi
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10459

Abstract

Steam turbines are essential components in steam power plants, converting thermal energy into mechanical energy to drive generators and produce electricity. Turbine blade damage can reduce efficiency and lead to plant trips, often accompanied by increased bearing vibration. This study investigates the root cause of low-pressure (LP) turbine blade failure at the Nagan Raya Steam Power Plant using the Root Cause Analysis (RCA) method. The results indicate that the failure was initiated by a 150 kV power system disturbance, which generated excessive blade vibration through the combined effects of backpressure and torsional resonance. The resulting cyclic stress exceeded the fatigue strength of the last-stage LP blade (L-0) on the generator side, causing blade fracture. Steam quality analysis confirmed abnormal operating conditions following the unit trip. Dye penetrant and magnetic particle inspections detected no surface cracks, while material composition analysis showed that the blade material met the specified standards. Scanning Electron Microscope (SEM) examination revealed clear evidence of high-cycle fatigue (HCF) at the fracture surface, confirming fatigue as the primary failure mechanism. These findings clarify the failure mechanism and provide recommendations to prevent similar incidents, thereby improving turbine reliability, operational stability, and maintenance strategies in steam power plants.
Pengaruh variasi jarak penyemprotan coating epoxy-aluminium terhadap kekuatan adhesi dan ketebalan lapisan pada baja SS400 Dimas Surya Fadli; Xander Salahudin; Nani Mulyaningsih
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10476

Abstract

SS400 steel lacks significant protective alloying elements, requiring an epoxy-aluminium coating whose effectiveness strongly depends on the adhesion strength between the coating and the substrate, with both adhesion and coating thickness affected by spray distance. This study aims to analyze the effect of spray distance variation (50, 100, and 150 mm) on the adhesion strength and thickness of an epoxy-aluminium coating applied to SS400 steel. A quantitative experimental method was employed, comprising surface preparation via sandblasting with 50/80 mesh glass beads, air spray application of the epoxy-aluminium coating, and testing of adhesion strength using a pull-off test (ASTM D4541-22) and coating thickness using a Dry Film Thickness gauge (ASTM D7091). The results show that adhesion strength increased with spray distance, from 9.1 MPa at 50 mm to 10.1 MPa at 100 mm and reaching the highest value of 10.9 MPa at 150 mm, while coating thickness decreased monotonically from 61.1 μm to 44.8 μm over the same range. A spray distance of 150 mm produced the highest adhesion strength together with the thinnest coating among the tested distances, and is therefore recommended as the best application parameter within the 50-150 mm range
Pengaruh penambahan serat bambu petung terhadap pengurangan kebisingan pada pelapisan komposit atap galvalum Vicky Zanuari Akbar; R. Faiz Listyanda; Agung Purnomo
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10471

Abstract

Rain-induced noise on galvalume roofing compromises a building's acoustic comfort, necessitating a coating material with effective sound-dampening properties. This study aims to analyze the effect of Petung bamboo fiber volume fraction on noise levels, the damping coefficient, and the adhesion strength of epoxy-matrix composites applied to galvalume roofing. An experimental study was conducted using composites fabricated via the hand lay-up method, incorporating Petung bamboo fibers treated with 5% NaOH and varying fiber volume fractions of 30%, 40%, 50%, and 60%. The results indicate that increasing the fiber volume fraction reduces noise levels while enhancing the damping coefficient and adhesion strength. The 60% variation yielded optimal performance, achieving a noise level of 82.767 dB, a damping coefficient of 0.854, and an adhesion strength of 2.483 MPa. These findings demonstrate the potential of Petung bamboo fiber composites as an eco-friendly coating material for galvalume roofing to improve acoustic performance and coating reliability
Pengaruh penambahan montmorillonite sebagai material filler terhadap karakteristik komposit berpenguat serat bambu petung Rozan Alifian D.; Aditya Noor Setyo Hadi D; Arbye S Arbye S
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10482

Abstract

This study aims to analyze the effect of adding montmorillonite (MMT) filler on the impact toughness, fire resistance, and fracture morphology of Petung bamboo fiber-oriented epoxy composites intended for boat hull applications. The bamboo fibers underwent a 20% Na₂CO₃ concentration soaking treatment for 48 hours. Composites were fabricated using the hand lay-up method with a 60% epoxy matrix and three variations of MMT filler-to-bamboo fiber volume fractions: 1%:39%, 2%:38%, and 3%:37%. Impact testing followed the ASTM E23 standard, while burning rate testing adhered to ASTM D635. The results indicate that increasing the MMT percentage reduced the composite's impact toughness due to particle agglomeration. The highest impact toughness was achieved by the 1% MMT variation (2.156 J; 0.022 J/mm²), characterized by ductile fiber pull-out fractures, whereas the 3% MMT variation yielded the lowest toughness (1.474 J; 0.015 J/mm²) with a brittle fracture pattern. Conversely, the addition of MMT significantly improved the composite's fire resistance through the formation of a char layer. The best (slowest) burning rate was obtained with the 3% MMT variation (2.6 mm/min), followed by 2% MMT (3.3 mm/min) and 1% MMT (5.31 mm/min).
Pengembangan modul pengajaran mata kuliah pemeliharaan sistem penggerak isuzu 10pd1 program studi pemeliharaan alat berat menuju pembelajaran mandiri Luki Indratmoko; Retno Susanti; Erik Tri Mahyudi; Bagas Prabowo; Cristian Cahya Putra
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10466

Abstract

The challenge in heavy equipment vocational education is the lack of student independence in learning due to a learning process that depends on lecturers and limited independent learning materials. This study aims to create a suitable, practical, and effective independent learning module for the Drive System Maintenance (ISUZU 10 PD1 Drive System) course in order to improve student learning outcomes and independence.This study used the Research and Development (RD) method with an adaptation of the 4D model.Data collection was carried out through validation by experts, questionnaires on practicality, learning outcome tests (pre-test and post-test), and learning independence questionnaires filled out by 30 test students.The results showed that: (1) The learning module (score of 4.43) and tutorial video (score of 4.30) were considered “Highly Valid” by experts, (2) The module was rated“Practical” for use by students with a score of 4.21 (84%). (3) The module was proven to be “Effective” in improving learning outcomes, as seen from the average N-Gain score of 0.58 (Moderate category). (4) The use of the module also succeeded in increasing student learning independence with a score of 4.22 (Very Good category).Based on these results, it is concluded that the self-directed learning module developed is suitable for use as teaching material to enhance understanding and learning independence among vocational students in heavy equipment technology.
Desain dan simulasi prototipe kapal pariwisata berbahan komposit ringan Muhammad Furqan; Bukhari Bukhari; Usman Usman
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10460

Abstract

This study aims to design and evaluate an Arduino Uno-based tourism boat prototype by considering hydrodynamic performance, stability, structural strength, and control system integration. The vessel was developed from the average principal dimensions of six reference boats, resulting in three design alternatives at a 25:100 scale. Maxsurf Modeler was used to generate the hull geometry, while Maxsurf Stability evaluated the stability parameters and Maxsurf Resistance, employing the Holtrop method, analyzed resistance at operating speeds of 10–30 knots. The best-performing design, which exhibited the lowest resistance at the highest speed, was further developed into a three-dimensional model using SolidWorks. Structural analysis of the Aluminium Alloy 6061-T bottom hull was conducted using Maxsurf Structure to assess its load-carrying capability. The selected design satisfied the International Maritime Organization (IMO) stability criteria, demonstrated sufficient structural strength, and achieved favorable hydrodynamic performance. Furthermore, the Arduino Uno-based remote-control system operated effectively, indicating the prototype's potential as a foundation for developing efficient, stable, and safe full-scale tourism vessels.
Rancang bangun dan analisis prototype automated guided vehicle (AGV) pengangkut toolkit bengkel perkakas berbasis kontrol PID Rafiqul Hidayat; Bambang Dwi Haripriadi
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10477

Abstract

Manual toolkit distribution in machining workshops causes production inefficiencies due to high operator downtime. Conventional navigation robots using infrared sensors often fail due to light reflections from oil spills and metal dust. This study aims to design and analyze a 0.5 kg Automated Guided Vehicle (AGV) prototype with a 1 kg payload capacity. Navigation is developed using two TCS34725 color sensors and a TCA9548A I2C multiplexer connected to an Arduino Mega 2560 to detect RGB and Clear values, rendering it oil-resistant. Movement stability is controlled by a PD algorithm driving an L298N driver and dual 1:48 DC gearbox motors, integrated with NRF24L01 wireless communication. Tuning results using the Ziegler-Nichols method determined optimal parameters at  and . This combination provides responsive steering, dampens oscillation, and eliminates integral windup during turns. Navigation tests demonstrated a 100% success rate in executing turns and station braking. At a 1 kg payload, the AGV achieved an average delivery time of 15.21 seconds compared to 11.32 seconds for manual delivery over an average distance of 12.5 meters. This is because increasing the payload mass raises the kinetic friction between the rubber wheels and the workshop floor, thereby reducing the AGV's linear speed at a constant PWM ratio
Optimasi desain struktur octagonal ring dynamometer menggunakan pendekatan parametric modeling berbasis makro untuk pengukuran gaya potong CNC milling Ilham Surya; Bukhari Bukhari; Mahmud Mahmud
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10472

Abstract

A dynamometer is an instrument used to directly measure the cutting force generated during a CNC milling process. Politeknik Negeri Lhokseumawe currently does not have a dynamometer to support laboratory practice and cutting-force research, so the development of an economical octagonal-ring-based dynamometer structure is required. This study applies parametric modeling based on Visual Basic for Applications (VBA) macros in SolidWorks to automate dimensional variation of the octagonal ring, and analyzes the effect of geometric variation on sensitivity, stress, factor of safety, stiffness, and natural frequency using Finite Element Analysis (FEA). Three geometric parameters were varied—side length (l), ring thickness (t), and ring width (b)—across seven dimensional combinations, each tested under fifteen loading scenarios (Fx, Fy, Fz at five points), producing 105 simulations. The VBA macro successfully automated parameter updates, model rebuilding, and simulation execution without manual intervention. Variation V1 produced the highest sensitivity but FOS 1, whereas variation V4 (l = 18 mm, t = 4 mm, b = 18 mm) was selected as the optimal design, increasing average sensitivity by 20% (Fx), 26.67% (Fy), and 35.29% (Fz) compared with the initial design, while maintaining a minimum factor of safety above 2 and a natural frequency of 130.49 Hz. This optimal design can serve as a reference for developing a physical dynamometer to support CNC milling machining practice and research
Analisis distribusi temperatur dan kecepatan aliran pada incinerator natural draft tipe fixed-grate menggunakan CFD Aditya Wahyu Ramadhan; Arif Rahman Saleh; Sigit Mujiarto; Rany Puspita Dewi
Jurnal Mesin Sains Terapan Vol 10, No 2 (2026): JURNAL MESIN SAINS TERAPAN
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jmst.v10i2.10483

Abstract

This study analyzes temperature distribution and gas-flow velocity in a 150 kg/batch natural-draft fixed-grate municipal solid waste incinerator using Computational Fluid Dynamics (CFD) in ANSYS Fluent 2023 R1. The numerical model activates the energy equation, standard k-epsilon turbulence, P1 radiation, Species Transport, and the Discrete Phase Model. Primary and secondary air inputs are 0.170 kg/s and 0.073 kg/s, respectively, while mesh independence is evaluated over several grid densities before the main simulation. The results show mass-weighted average temperatures of 1637.15 K in the primary chamber, 1169.62 K in the secondary chamber, and 1058.23 K at the outlet. Average velocity increases from 0.795 m/s in the primary chamber to 2.437 m/s in the secondary chamber and reaches 23.443 m/s at the outlet. The highest thermal zone is concentrated in the primary chamber, whereas flow acceleration occurs downstream due to secondary-air momentum and changes in cross-sectional area. Local recirculation appears in the secondary chamber, and outlet backflow is associated with the pressure-outlet boundary and the incomplete chimney geometry. These results show a coupled thermal-flow pattern that can support further optimization of air distribution and incinerator geometry.