cover
Contact Name
A. Jannifar
Contact Email
polimesin@pnl.ac.id
Phone
+628126930456
Journal Mail Official
polimesin@pnl.ac.id
Editorial Address
Politeknik Negeri Lhokseumawe Jl. Banda Aceh-Medan Km 280 Buketrata, Lhokseumawe, 24301, Aceh, Indonesia
Location
Kota lhokseumawe,
Aceh
INDONESIA
Jurnal Polimesin
ISSN : 16935462     EISSN : 25491199     DOI : http://dx.doi.org/10.30811/jpl
Polimesin mostly publishes studies in the core areas of mechanical engineering, such as energy conversion, machine and mechanism design, and manufacturing technology. As science and technology develop rapidly in combination with other disciplines such as electrical, Polimesin also adapts to new facts by accepting manuscripts in mechatronics. In Biomechanics, Mechanical study in musculoskeletal and bio-tissue has been widely recognized to help better life quality for disabled people and physical rehabilitation work. Such a wide range of Polimesin could be published, but it still has criteria to apply mechanical systems and principles. Exceeding the limitation has been a common reason for rejection by those outside the scope. Using chemical principles more than mechanical ones in material engineering has been a common reason for rejection after submission. Excessive exploration of the management within the discipline of Industrial Engineering in the manufacturing technology scope is also unacceptable. The sub-scope biomechanics that focuses on ergonomics and does not study movement involving applied force on the bio-tissue is also not suitable for submission.
Articles 664 Documents
Catalytic co-pyrolysis of PET waste and used cooking oil over natural zeolite: effects of feedstock ratio on bio-oil yield, energy efficiency, and fuel quality Dianta Mustofa Kamal; Denny Yatmadi; Tatun Hayatun Nufus; Ridwan Ridwan
Jurnal Polimesin Vol 24, No 5 (2026): October
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jpl.v24i5.9198

Abstract

Despite extensive research on plastic and oil pyrolysis, many studies have evaluated liquid yield, energy efficiency, and fuel quality separately, thereby limiting the integrated assessment of the process. This study investigates the catalytic co-pyrolysis of Polyethylene Terephthalate (PET) waste and used cooking oil over natural zeolite, with simultaneous evaluation of liquid yield, electrical energy efficiency, and fuel properties. Experiments were conducted at 500 °C for 90 min in a batch reactor equipped with a water-cooled condenser. PET-to-oil ratios of 1:2, 2:1, 1:1, 3:1, 1:3, and 1:0 were tested at a fixed catalyst loading of 5 wt%. Among the tested compositions, the 1:1 ratio produced the highest reported liquid yield (21.99%) and liquid-energy-to-electrical-input metric (35.06%). The corresponding liquid product had a calorific value of 44.13 MJ/kg, a density of 0.8177 g/cm³, and a kinematic viscosity of 1.2711 mm²/s. The reported density and viscosity values were compared numerically with the Indonesian B35 (CN 48) reference ranges. These results identify a favorable laboratory-scale operating condition for PET–used-cooking-oil co-processing. However, because the experiments were single-point measurements, no catalyst-free control was included, total feedstock loading was not identical across archived runs, and complete gas/char balances were unavailable, the results should be interpreted as an operating-window demonstration rather than a definitive quantification of feedstock-ratio effects, catalytic synergy, or scale-up feasibility.
An integrated metallurgical approach to failure diagnosis of SA210 grade A1 boiler economizer tubes Rio Pudjidarma Santoso; Winarto Winarto; Jaka Fajar Fatriansyah
Jurnal Polimesin Vol 24, No 5 (2026): October
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jpl.v24i5.9528

Abstract

SA210 Grade A1 steel is widely used for economizer and waterwall tubes in subcritical boilers. In these components, local overheating can degrade the ferrite–pearlite microstructure before severe wall thinning becomes apparent. This study evaluates an integrated metallurgical approach that combines degradation-stage identification and relative hardness loss with dimensional and operating evidence for failure diagnosis of SA210 Grade A1 economizer tubes. Controlled accelerated exposure was performed at 600–720 °C for 1–100 h, followed by optical metallography and Vickers hardness testing. The resulting microstructures were classified from Stage A to Stage F. Progressive thermal exposure produced lamellar fragmentation, carbide spheroidization, carbide coarsening, and a corresponding decrease in hardness. The most severe laboratory condition produced Stage F degradation with a 27.4% relative hardness loss. Two failed economizer tubes exhibited comparable Stage F-type microstructures and substantial relative hardness reductions of 27.2% and 30.6%, while their remaining wall thicknesses were above the calculated minimum requirement. The latter value was derived from an instrument-converted portable hardness measurement and was regarded as supporting field evidence, not as a direct substitute for laboratory Vickers hardness. Taken together, the evidence was most consistent with overheating-induced metallurgical degradation, whereas the available data did not support generalized wall thinning or a recorded pressure excursion as the primary driver. The approach can identify severe thermal degradation that may not be evident from thickness measurement alone, but it is not a standalone remaining-life model.
Empirical modeling to predict the corrosion inhibition of carbon steel using cempedak peel (Artocarpus integer) extract in 3.5% NaCl solution Yumaidi Saputra; Nurdin Ali; Syarizal Fonna; Putri Ramadhani; Husni Usman
Jurnal Polimesin Vol 24, No 5 (2026): October
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jpl.v24i5.9297

Abstract

Preventing corrosion in carbon steel is essential to preserve its structural integrity and performance and to minimize associated economic losses. One of the primary strategies involves the use of corrosion inhibitors derived from sustainable organic materials. In general, the corrosion rate is determined experimentally, but this approach requires substantial resources, is less economical, and takes a relatively long time. Therefore, there is a need for a more efficient and renewable method. This study aimed to develop an empirical model to predict inhibitor performance based on experimental data on weight loss in metal exposed to a corrosion environment of 3.5% NaCl and a mixture of cempedak fruit peel (Artocarpus integer) inhibitors. The model was developed using a power-law equation to identify the correlation between inhibitor concentration and exposure time, with the resulting equation being Cr (t, C) = a (C) × tb(C). The experimental results show that the corrosion rate decreases with increasing exposure time and inhibitor concentration. These results are consistent with the trend line in the developed model, and the error values for the experimental results were 10.61, 7.56, 11.49, 8.04, 4.41, and 2.44%, respectively, for concentrations of 0, 200, 400, 600, 800, and 1000 mg/L. The proposed model can be applied to predict the effectiveness of inhibitors in protecting metals from corrosion.
Design and experimental validation of pulley-based residence-time control in a continuous tubular screw torrefaction reactor Agus Apriyanto; Retno Wahyudi; Hafizd Zakiyun Alrasyid
Jurnal Polimesin Vol 24, No 5 (2026): October
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jpl.v24i5.9146

Abstract

Residence time is a key control variable in continuous torrefaction because it determines the duration of biomass exposure to the thermal environment. This study develops a pulley-driven method that converts a target residence time into screw rotational speed, driving-pulley diameter, and belt length without changing the reactor body or gearbox. Three targets (10, 20, and 30 min) were designed for a continuous oil-jacketed tubular screw reactor with a 1:60 gearbox and validated experimentally. Each pulley configuration was tested in five repeated residence-time measurements using a 100 g test charge and manual stopwatch timing. The designed pulley diameters were 10.9, 19.33, and 29 cm, with corresponding belt lengths of 133.32, 147.80, and 164.54 cm. Experimental residence times were 9.85 ± 0.54, 20.71 ± 0.49, and 30.06 ± 0.35 min (mean ± SD, n = 5), corresponding to absolute mean errors of 1.50%, 3.55%, and 0.20%, respectively. The results show that discrete pulley replacement can provide repeatable, mechanically simple residence-time settings under the tested conditions. The contribution is a transparent design-to-validation workflow linking target residence time directly to transmission geometry. Because feedstock properties and full thermal operating conditions were not independently characterized in the validation dataset, the findings should be interpreted as validation of mechanical residence-time control rather than torrefaction-product performance.
Experimental evaluation of a modified pushing arm for improved potato cutting machine performance Satrio Darma Utama; Sukadi Sukadi; Sandi Yudha Barri Zaki
Jurnal Polimesin Vol 24, No 5 (2026): October
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jpl.v24i5.9158

Abstract

Potato cutting machines used by household industries and small- and medium-sized enterprises require stable pushing mechanisms to improve productivity and reduce vibration. This study experimentally evaluated the performance of a potato cutting machine after modifying the pushing-arm geometry. The original 570 mm arm was compared with 300 mm and 190 mm configurations. Finite element analysis provided a preliminary structural check, while the main evaluation was conducted experimentally. The prototype was tested using 1 kg potato samples and a cutting blade with a 14 mm slot width. Cutting time, vibration, electrical power, operating energy, and productivity were measured. The optimized 190 mm arm reduced cutting time from 160 to 35 s/kg, representing a 78.1% reduction compared with the original design. Vibration decreased from 4.2 to 2.1 mm/s, while average electrical power remained constant at 390 W. Operating energy consequently decreased from 62.40 to 13.65 kJ/kg, and productivity increased from 22.5 to 102.9 kg/h. Preliminary structural analysis indicated that the optimized arm remained below the yield strength of AISI 1020 steel under the modeled static load. These results demonstrate that modifying the pushing-arm geometry can improve cutting productivity, reduce vibration, and decrease energy consumption per unit mass.
Effect of E-glass fiber content on the tensile and compressive properties of epoxy composites Sudirman Lubis; Munawar Alfansury Siregar; Rafsanzani Pane
Jurnal Polimesin Vol 24, No 5 (2026): October
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jpl.v24i5.9097

Abstract

Epoxy composites reinforced with natural or synthetic fibers have attracted considerable attention as lightweight engineering materials. However, their mechanical performance depends on reinforcement content and requires systematic evaluation. This study investigated the tensile and compressive behavior of epoxy composites reinforced with E-glass fiber at contents of 10, 20, and 30 wt.%, corresponding to epoxy-to-reinforcement ratios of 90:10, 80:20, and 70:30, respectively. Tensile and compressive tests were conducted using a universal testing machine in accordance with ASTM D3039 and ASTM D695, respectively. The mean tensile strength increased from 48.02 ± 17.39 MPa at 10 wt.% E-glass fiber to 59.12 ± 10.19 MPa at 20 wt.% and 70.45 ± 5.36 MPa at 30 wt.%. However, one-way analysis of variance showed that these differences were not statistically significant at the 5% significance level (p = 0.154). The compression curves showed different load–deformation responses across the reinforcement contents, but compressive strength could not be compared quantitatively because the numerical stress scale and units in the available figures could not be verified. Overall, tensile strength showed an increasing trend with increasing E-glass fiber content, although this trend was not statistically significant. Further evaluation using verified compressive data and additional mechanical and material characterization is needed to establish the suitability of these composites for specific engineering applications.
Effect of fiber orientation on the mechanical properties of sisal/e-glass/epoxy composites containing spent coffee ground-derived activated carbon Darul Ikrami; Adi Setiawan; Muhammad Muhammad; Reza Putra; Lies Banowati; Faizar Rianda
Jurnal Polimesin Vol 24, No 5 (2026): October
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jpl.v24i5.9852

Abstract

Despite the development of natural/synthetic fiber hybridization and the use of bio-fillers have been widely studied, limited knowledge still exists regarding the simultaneous integration of activated carbon of Arabica coffee grounds into sisal/E-glass/epoxy hybrid composites and the effect of fiber orientation variations on their mechanical performance. This research presents a novelty through the development of lightweight hybrid biocomposites based on coffee grounds waste and sisal/E-glass fiber with fiber orientation evaluation. The composite was fabricated using the hand lay-up method with orientation variations of 90°/0°, 0°/90°, and ±45°/45°. The tensile test referred to ASTM D3039, while the microstructure analysis was performed using SEM-EDS. The results showed that the 0°/90° orientation resulted in the highest tensile strength (36.27 MPa) due to the dominance of direct axial load-bearing, while the orientation ±45°/45° resulted in the highest modulus of elasticity (9.36 MPa) through the in-plane shear distribution. SEM observations confirmed the failure mechanisms of fiber fracture, pull-out, matrix cracking, and debonding. The key scientific contributions of the study is to provide an in-depth understanding of the trade-off mechanism between axial load holding capacity and elastic shear response, while providing engineering design guidance for sustainable lightweight structure applications.
Motorcycle oil temperature and optocoupler-based RPM oil condition monitoring system using IoT Sudiro Sudiro; Dewandono Bayu Seto; Wachid Yahya; Apri Widyastanto; Onery Andy Saputra
Jurnal Polimesin Vol 24, No 5 (2026): October
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jpl.v24i5.9175

Abstract

Motorcycle engine oil condition is essential for maintaining engine performance and preventing excessive component wear. Conventional oil replacement indicators commonly rely on mileage or service intervals and do not represent actual oil condition during operation. This study proposes a low-cost Internet of Things (IoT)-based monitoring system that uses oil temperature and RPM response as indirect indicators of oil condition rather than directly measuring oil viscosity. The system integrates a K-type thermocouple with a MAX6675 module, a DC motor and propeller mechanism, an optocoupler sensor, Arduino Uno R3, ESP32, and the Blynk IoT platform. Experimental testing included sensor calibration and validation, oil loading tests, and IoT monitoring and notification tests. The temperature measurement showed an average absolute error of 0.94°C, while the RPM measurement using the optocoupler showed an average error of approximately 1.61%. The oil loading test showed that the developed prototype could identify changes in rotational resistance through RPM response, with 7140 RPM used as the experimental threshold for the tested oil condition. Monitoring data were transmitted to the Blynk platform at 1-second intervals with warning notifications provided through the application and email. The results demonstrate the feasibility of RPM response as an indirect oil condition indicator for a low-cost IoT monitoring system. Further validation using standard viscosity measurements and oil samples with different degradation levels is therefore required.
Biodiesel production from waste cooking oil using a CaO/C/KOH composite catalyst: Effects of transesterification time and oil-to-methanol molar ratio Syarifuddin Oko; Andri Kurniawan; Muh. Irwan; Mustafa Mustafa; Wahyudi Wahyudi; Rahma Anggraini; Annisa Gunarti
Jurnal Polimesin Vol 24, No 5 (2026): October
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jpl.v24i5.9149

Abstract

Waste cooking oil (WCO) is a potential renewable feedstock for biodiesel production, although its degradation products and contaminants require appropriate treatment. This study investigated the effects of transesterification time and oil-to-methanol molar ratio on biodiesel yield and fuel properties using a CaO/C/KOH composite catalyst. After esterification to reduce the free fatty acid (FFA) content, transesterification was conducted at 60 °C using 3 wt% catalyst. The oil-to-methanol molar ratio was varied from 1:3 to 1:15 at a reaction time of 3 hours, while reaction time was varied from 1 to 5 hours at a molar ratio of 1:15. Biodiesel was characterized in terms of yield, density, viscosity, acid number, moisture content, and methyl ester composition, with fuel properties assessed against the SNI 7182:2015 standard. The highest reported yield was 80.02%, with a methyl ester content of 99.77%, at a reaction time of 3 hours. At an oil-to-methanol molar ratio of 1:15, the reported yield was 71.9%, with a methyl ester content of 99.19%. GC–MS analysis identified methyl oleate and methyl palmitate as the dominant components. The characterization results indicated that the biodiesel met the specified SNI 7182:2015 requirements. These findings demonstrate the potential of the CaO/C/KOH composite catalyst for biodiesel production from WCO and highlight the importance of optimizing reaction conditions.
Heatsink geometry effect on the thermal performance of a waste heat thermoelectric generator: experimental and CFD analysis Sugiyanto Sugiyanto; Nyayu Aisyah; Yosephus Ardean Kurnianto Prayitno; Irfan Bahiuddin
Jurnal Polimesin Vol 24, No 5 (2026): October
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jpl.v24i5.8881

Abstract

Thermoelectric Generators (TEGs) offer a promising approach for recovering waste heat from diesel exhaust. However, their performance strongly depends on maintaining a sufficient temperature difference between the hot and cold sides of the module, making the design of the cold-side cooling system particularly important. This study investigates the effect of heatsink geometry on the thermal performance of a waste-heat TEG system integrated with a diesel generator. Three heatsink configurations, designated as P90; P120, and P150 are examined at an engine speed of 780 RPM and 1500 RPM. This analysis combines Experimentation and Computational Fluid Dynamics (CFD). Evaluated numerical results include temperature contours, thermal gradients, and temperature difference delta (ΔT) across TEG.  The experimental system employed K-type thermocouples connected to an ESP32-based data acquisition system to measure the thermal response of the TEG under controlled operating conditions. The CFD model was used to evaluate the conjugate heat-transfer process between the exhaust-side components, TEG module, heatsink, and cooling airflow. The results indicate that increasing the heatsink size generally improves heat dissipation from the cold side and increases ΔT across the TEG. At 780 RPM, the CFD results showed ΔT values of 20.201, 20.337, and 20.455 °C for P90, P120, and P150, respectively, indicating a limited influence of heatsink geometry under lower thermal input conditions. At 1500 RPM, the corresponding ΔT values increased to 38.877, 42.129, and 44.168 °C, demonstrating a more pronounced effect of heatsink geometry under higher thermal and airflow conditions. Experimental results exhibited a similar increasing trend, although differences in the absolute ΔT values were observed. The findings demonstrate that heatsink geometry becomes increasingly important as the available exhaust heat and cooling airflow increase. This study provides a comparative evaluation of heatsink configurations for improving the thermal management of TEG-based waste heat recovery systems in diesel generator applications.