cover
Contact Name
-
Contact Email
-
Phone
-
Journal Mail Official
-
Editorial Address
Redaksi Jurnal Rekayasa Mesin Jurusan Teknik Mesin Fakultas Teknik, Universitas Brawijaya Jl. MT. Haryono 167 Malang, Jawa Timur Indonesia 65145
Location
Kota malang,
Jawa timur
INDONESIA
Rekayasa Mesin
Published by Universitas Brawijaya
ISSN : 23381663     EISSN : 24776041     DOI : 10.21776/ub.jrm
Core Subject : Engineering,
Rekayasa Mesin is published by Mechanical Engineering Department, Faculty of Engineering, Brawijaya, Malang-East Java-Indonesia. Rekayasa Mesin is an open-access peer reviewed journal that mediates the dissemination of academicians, researchers, and practitioners in mechanical engineering. Rekayasa Mesin accepts submission from all over the world, especially from Indonesia. Rekayasa Mesin aims to provide a forum for national and international academicians, researchers and practitioners on mechanical engineering to publish the original articles. All accepted articles will be published and will be freely available to all readers with worldwide visibility and coverage. The scope of Rekayasa Mesin are the specific topics issues in mechanical engineering such as design, energy conversion, manufacture, and metallurgy. All articles submitted to this journal can be written in Bahasa and English Language.
Arjuna Subject : -
Articles 1,007 Documents
Increased the Surface Hardness of Recycled Piston Waste by Variation of Shot Pressure in Shot-Peening Method Priyambodo, Bambang Hari; Setiawan, Widia; Santoso, Nugroho; Athaillah , Fakhri; Palmiyanto, Martinus Heru; Priyanto, Kaleb
Jurnal Rekayasa Mesin Vol. 17 No. 2 (2026)
Publisher : Jurusan Teknik Mesin, Fakultas Teknik, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/ub.jrm.v17i2.2133

Abstract

The increasing demand for aluminium in the motorcycle industry has led to significant concerns regarding sustainability and resource utilization. Recycling aluminium waste, particularly from discarded motorcycle pistons, presents a viable solution to address material shortages and reduce environmental impact. This study explores the effects of shot-peening treatment on recycled aluminium derived from motorcycle piston waste, aiming to enhance its mechanical properties and microstructural characteristics. Recycled aluminium specimens were produced through sand casting and subsequently subjected to shot-peening at varying pressures of 5, 6, 7, and 8 bar for 20 minutes. The hardness measurements revealed a substantial improvement, with values recorded as 107, 144, 171, and 209 HV, respectively, demonstrating a 170% increase at the highest pressure compared to untreated specimens. Microstructural analysis indicated notable changes, including increased density, grain refinement, and the formation of a hardened surface layer. The depth of the modified layer ranged from 50 to 200 μm, depending on the applied pressure. Furthermore, shot-peening induced compressive residual stress, which is beneficial for improving fatigue resistance and overall durability. These findings suggest that optimizing shot-peening parameters can significantly enhance the performance of recycled aluminium, making it a promising material for various industrial applications. This study contributes to sustainable manufacturing practices by promoting the reuse of aluminium waste, reducing reliance on virgin materials, and supporting circular economy principles. The implementation of shot-peening in aluminium recycling has the potential to improve material properties, expand its industrial applicability, and minimize environmental impact in the transportation and manufacturing sectors.
Design and Development of a 70 Kg Capacity HDPE Hot Press Machine to Support SDGs Programs in the Polin ATMI and Industrial Kumbarasari, Shanti; Nugroho, Oktavianus Ardhian; Setiady, Wahyu; Agripa, Jordhan Imanuel
Jurnal Rekayasa Mesin Vol. 17 No. 2 (2026)
Publisher : Jurusan Teknik Mesin, Fakultas Teknik, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/ub.jrm.v17i2.2165

Abstract

Plastic is one of the most widely used materials in Indonesia. One type is HDPE (High-Density Polyethylene) plastic, this type is most widely used in daily life and one of the largest contributors of plastic waste. Despite its recyclability HDPE have recyclable properties, therefore the recycling process needs to be carried out immediately. Polin ATMI and ATMI Recycle Studio in collaboration with PT. AISIN Indonesia together conducted research to make a high-capacity hydraulic hot press machine of 70 Kg a day. The purpose of this research is to make a large-capacity machine that can recycle plastic which is then used as a plate that can be used for making furniture and crafts. In addition, the manufacture of this machine aims to support the SDGs program that is being carried out by PT. AISIN Indonesia. The morphological matrix method was used in the initial design process similar to the manufacture of a hot press plastic machine. The result of this research is that it has succeeded in making a plastic hot press machine with a total dimension of 1.5 m x 1.55 m x 1.55 m and the resulting product is in the form of a plate with a size of 1.3 m2 and a thickness of 0.2 m.
Surface Hardening of Mild Steel: The Role of Carbon Source in Pack Carburizing on Hardness and Microstructure Atmoko, Nugroho Tri; Margono, Margono; Wijayanto, Hendi Lilih; Supriyanto, Agung; Tarigan, Roy Aries Permana
Jurnal Rekayasa Mesin Vol. 17 No. 2 (2026)
Publisher : Jurusan Teknik Mesin, Fakultas Teknik, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/ub.jrm.v17i2.2178

Abstract

One effective approach to improve the surface hardness of steel is pack carburizing, in which carbon is introduced into the surface in a sealed chamber. This study investigates the effect of different carbon powder media on the surface hardness and microstructure of low-carbon steel subjected to pack carburizing. Three carbon sources were employed: bamboo charcoal, coconut shell charcoal, and beef bone charcoal. Each carburizing medium was prepared by mixing 70 wt.% carbon powder with 30 wt.% Ba₂CO₃ energizer. The carburized specimens were characterized by Vickers hardness testing and optical metallography to evaluate hardness response and carbon diffusion depth. The results show that pack carburizing significantly increases surface hardness, with the highest hardness obtained with bamboo charcoal, reaching 416.4 HVN, corresponding to a 59.4% increase over the base material's hardness of 156.8 HVN. Microstructural observations confirm that the carbon diffusion depth depends strongly on the carbon source, with the greatest depth of 538 μm from the surface also observed with bamboo charcoal. These findings indicate that bamboo-based carbon media are particularly effective for enhancing the surface properties of low-carbon steel through pack carburizing.
Analysis on the Improvement to the Mechanical Properties of ASTM A36 Using Spot Hardfacing Method Awali, Jatmoko; Rohimsyah, Fikan Mubarok; Ismail , Andi Idhil; Dewanto , Hizkia Alpha; Al-Shehan, Khulafaur Nawaf; Akram, Muhammad; Yusuf, Chiara; Triana, Yunita; Zulfikar, Ainun
Jurnal Rekayasa Mesin Vol. 17 No. 2 (2026)
Publisher : Jurusan Teknik Mesin, Fakultas Teknik, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/

Abstract

Hardfacing is considered to be an optimum, lightweight method to improve the strength of electrical vehicle chassis to be used in many places with variable road conditions in Indonesia, especially around the New National Capital (IKN) area. In this study, carbon steel (ASTM A36) plates were strengthened by spot hardfacing using an ER70S-6 electrode. Variables used in this study are weld dwelling time (4, 7, and 10 seconds with a constant distance of 30 mm) and spot distance (20, 30, and 40 mm with a 7 second dwelling time). From this study, the increase of dwelling time and the decrease of the spot distance enhanced the toughness of the specimens. Further observations discovered that both dwelling time increase and spot distance decrease correlated to the increase of the average grain size of the phases present in the specimens. The optimum variations observed in this research are 10 seconds dwelling time of 1,321-1,508 J/mm2 and 20 mm of spot distance of 1,312-1,456 J/mm2.
Tailoring Phase Transformation of Calcium-Zirconia on Structural ond Mechanical Properties Setopratama, Andyan Rafi; Nehan, Phahul Zhemas Zul; Latief, Faried; Wismogroho, Agus Sukarto; Triwikantoro, Triwikantoro; Sulistijono, Sulistijono; Widyastuti, Widyastuti
Jurnal Rekayasa Mesin Vol. 17 No. 2 (2026)
Publisher : Jurusan Teknik Mesin, Fakultas Teknik, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/

Abstract

Developing sustainable stabilizers for zirconia extracted from natural zircon sand is essential to reduce reliance on conventional commercial additives while improving resource utilization. This study investigated the effects of calcium concentration and calcium source on the structural evolution and mechanical properties of zirconia synthesized via an alkali fusion–coprecipitation process. Seven samples were synthesized using eggshell-derived and commercial calcium dopants at concentrations of 0–1.5 mol%. Raman spectroscopy confirmed the dissociation and recombination of Si–O bonds in the ZrSiO4 lattice and the formation of ZrO2, while X-ray fluorescence verified a ZrO2 purity of 85.712 wt.%. X-ray diffraction revealed that calcium doping expanded the lattice parameter (c-axis: 5.100–5.180 Å), increased tetragonality (c/a up to 1.4420), reduced microstrain (109.2 × 10-4 to 51.8 × 10-4), increased crystallite size (7.4–8.3 nm), and nonlinearly enhanced the tetragonal phase fraction, reaching 7.2 wt.% at 1.0 mol% commercial calcium before declining at higher concentrations. Sintering at 1400 °C for 3 h completely transformed the tetragonal phase into the monoclinic phase. Eggshell-derived calcium at 0.5 mol% exhibited the best density (4.055 g/cm3), lowest porosity (19.447%), and greatest Vickers hardness (142.2 HV), comparable to commercial calcium. These findings suggest that calcium derived from eggshells is a viable and sustainable alternative stabilizer for zirconia ceramics, whilst also promoting the utilization of waste.
Operating-Point Optimization of an Organic Rankine Cycle Under Variable Waste Heat Conditions: An Energy Exergy Mahmuddin, Mahmuddin; Habib, Faisal; Pakka, Hariani
Jurnal Rekayasa Mesin Vol. 17 No. 2 (2026)
Publisher : Jurusan Teknik Mesin, Fakultas Teknik, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/

Abstract

Low-grade waste heat varies in thermal quality and can shift an Organic Rankine Cycle (ORC) away from favorable operating conditions. This study evaluates operating-point optimization of a single-pressure subcritical ORC using integrated energy and component-level exergy analyses. R245fa was used as the reference fluid, while R245fa/R1233zd(E) mixtures were examined for composition and temperature-matching effects. At a heat-source temperature of 150 °C, increasing evaporation pressure from 1.5 to 3.0 MPa raised thermal efficiency from 11.912% to 14.311%. A pressure of 2.8 MPa was retained as the reference near-optimal point, yielding 33.976 kW net power on a 1.0 kg/s working-fluid basis, 14.164% thermal efficiency, and 48.739% exergy efficiency. Increasing pressure to 3.0 MPa improved net power by only 0.57% while reducing the evaporator hot-end temperature difference from 10.7 to 7.0 K. At 2.8 MPa, total exergy destruction was 35.734 kW, distributed among the evaporator (54.16%), expander (23.49%), condenser (20.58%), and pump (1.77%). The 0.3/0.7 R245fa/R1233zd(E) mixture was the first feasible composition under the 5 K minimum temperature-difference constraint and gave the highest feasible thermal efficiency, 14.636%, or 0.472 percentage points above pure R245fa, with a temperature glide of 0.528 K. This modest gain is associated with composition-dependent source–fluid temperature matching under the imposed feasibility constraint rather than an unconstrained interior optimum. Under a 140-160 °C heat-source variation, operating-point adjustment limited the maximum relative net-power deviation to approximately ±1.8%. Raising condensation temperature from 30 to 40 °C reduced both thermal and exergy efficiencies by about 8.96%, while increasing expander isentropic efficiency from 0.80 to 0.88 raised exergy efficiency from 48.739% to 53.990%. The study integrates operating-point adaptation, mixture assessment, and component-level thermodynamic diagnosis within a simple ORC framework for variable waste-heat recovery.
EFFECT OF LOADING CONFIGURATION ON MIXED-MODE DELAMINATION BEHAVIOR OF LAMINATED COMPOSITES Wahjudi, Ari; Purnowidodo, Anindito; Widodo, Agung Sugeng; Anam, Khairul
Jurnal Rekayasa Mesin Vol. 16 No. 3 (2025)
Publisher : Jurusan Teknik Mesin, Fakultas Teknik, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/jrm.v16i3.2559

Abstract

Delamination is a critical interlaminar failure mode in laminated composites, particularly under mixed-mode loading where opening and shear mechanisms interact during crack propagation. This study investigates the effect of loading configuration and displacement ratio on mixed-mode delamination behavior using a finite element model incorporating finite-thickness cohesive zone elements. Three loading configurations, namely single-leg bending (SLB), modified single-leg bending (MSLB), and mixed-mode bending (MMB), were investigated. For MSLB and MMB, five additional-to-primary displacement ratios ranging from 0.5 to 2.5 were applied. Delamination behavior was evaluated in terms of load-displacement response, delamination area, and mode-mixity evolution. The results showed that increasing the displacement ratio increased the delamination area in both MSLB and MMB configurations. The MSLB delamination area increased from 15.04 to 30.71 mm², whereas the MMB area increased from 24.53 to 50.80 mm². MSLB exhibited a transition from predominantly shear-controlled toward greater opening contribution as the displacement ratio increased, while MMB remained predominantly shear-controlled during most of the propagation process. Among configurations with comparable maximum loads, MSLB 1.5 produced a smaller delamination area of 21.37 mm² than SLB of 23.90 mm², and MMB 1 of 28.96 mm². These findings demonstrate that mixed-mode delamination is governed by the interaction between loading configuration, displacement ratio, and evolving mode-mixity. The finite-thickness cohesive-zone approach provides an effective numerical framework for evaluating delamination propagation under different mixed-mode loading conditions.

Page 101 of 101 | Total Record : 1007