Claim Missing Document
Check
Articles

Found 31 Documents
Search

The Study of Plant Microbial Fuel Cell for Alternative Energy Source Melda Latif; Paskalina Aprila Tiy; Mumuh Muharam; Aulia; Amirul Luthfi
JURNAL NASIONAL TEKNIK ELEKTRO Vol 12, No 2: July 2023
Publisher : Jurusan Teknik Elektro Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/jnte.v12n2.1061.2023

Abstract

Plant Microbial Fuel Cell (P-MFC) is one of Microbial Fuel Cell type. It can produce electricity and source for plant living. By using the humus soil in the anode chamber, the electron can flow to the cathode chamber. The principle of Plant Microbial Fuel Cell is same with the battery. It flows the direct current. This research makes dual chamber of P-MFC prototype. The salt bridge is used as connection between anode chamber to cathode chamber. The humus soil comes from burning organic waste. Its color is black and contains a lot of microbes. The plant selected in this research was Water Spinach. The number of water spinach were 20 and 25 stems. P-MFC which has more Water Spinach will produce more voltage and current than the others. For 25 Water Spinach, P-MFC produced 762.4 mV no-load average voltage and 125.8 mV, 085 mA for load condition. The result was bigger caused by for more plants will be more microbes resulted in the humus soil.
Enhancing Current Density and Specific Capacitance through Tensile TEMPO, Bacterial Cellulose and Polypirrole Nanocomposites Syukri Yunus; Muhammad Fajar Ruhud Manurung; Aulia Aulia; Yanuar Zulardiansyah Arief
Andalasian International Journal of Applied Science, Engineering and Technology Vol. 4 No. 1 (2024): March 2024
Publisher : LPPM Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/aijaset.v4i1.118

Abstract

The researchers developed a bio-composite film material that serves as a substitute for metal. The materials used are TEMPO ((2,2,6,6-tetramethylpiperidine-1-oxyl)), Bacterial Cellulose, and Polypyrrole (Ppy). This research aimed to increase the material's current density and specific capacitance values using the drawing method. Composite nanomaterials are made by oxidizing BC (Bacterial Cellulose) with TEMPO. The resulting TOBC (TEMPO Bacterial Cellulose) material was mixed with Ppy using the in situ method. The mixture is then drawn wet—measurement of current density and capacitance using Cyclic Voltammetry (CV) Testing. The current density and specific capacitance results increased by 542.74% and 754.79% after drawing the nanocomposite material. It is directly proportional to the effects of characteristic testing, which includes SEM, XRD, and FTIR. As a result of the withdrawal of the polypyrrole, it will be more evenly distributed in the composite material, absorbing and coating the nata de coco. The researchers concluded that when the TOBC/Ppy fibers are straighter and denser, they achieve higher current density and capacitance values.
Analysis of Exhaust Gas Heat Utilization in Waste Heat Recovery Power Generator at Indarung V Factory PT Semen Padang Mayang Safira; Melda Latif; Zaini Zaini; Aulia Aulia; Mumuh Muharam; Waweru Njeri
Andalas Journal of Electrical and Electronic Engineering Technology Vol. 3 No. 1 (2023): May 2023
Publisher : Electrical Engineering Dept, Engineering Faculty, Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/ajeeet.v3i1.34

Abstract

Increasing energy efficiency in the cement production process at PT Semen Padang is carried out by reusing exhaust gas to produce electricity using Waste heat recovery power generation (WHRPG) with a capacity of 8.5 MW. WHRPG is a technology for utilizing exhaust gas heat as a source of heat energy to heat feed water into steam by using a suspension preheater (SP) boiler and air quenching cooler (AQC) boiler. This study aims to calculate the power potential of the steam heat influenced by the steam temperature and the mass flow rate of the steam produced by the boiler, to calculate the efficiency of the boiler using the direct method by comparing the boiler output heat against the boiler input heat, to calculate the turbine efficiency based on the difference between the steam enthalpy enter the turbine against the steam enthalpy out of the turbine and the isotropic enthalpy of the steam out of the turbine and to calculate the power generated by WHRPG at PT Semen Padang. The results obtained in this study are the total potential power of steam heat is 19.778 MW, the boiler AQC efficiency is 70.30%, the boiler SP efficiency is 94.04% and the turbine efficiency is 78.64%. The electricity generated by PT Semen Padang's WHRPG is 3.70 MW.
Enhancing Current Density and Specific Capacitance of Nata de Coco, TEMPO, and MXene Composites through Boiling Time Variations Yunus, Syukri; Umah, Kuntum Khairah; Abral, Hairul; Ogah, Ogah Anselm; Aulia, Aulia
Andalasian International Journal of Applied Science, Engineering and Technology Vol. 3 No. 3 (2023): November 2023
Publisher : LPPM Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/aijaset.v3i3.110

Abstract

This research aimed to enhance the current density and specific capacitance of electronic device materials to replace traditional metal materials. Composite materials that include Nata de Coco, TEMPO (2,2,6,6-tetramethylpiperidine-1-oxyl), and MXene achieve this improvement. Composite materials that include Nata de Coco, TEMPO, and MXene accomplish this improvement. Initial testing has shown that these materials initially demonstrated lower electrical properties, particularly in current density and specific capacitance, than conventional metals. To enhance their electrical properties, we employed a boiling method with variations in boiling time. The time intervals chosen were 30, 300, and 480 minutes. In the manufacturing process, Nata de Coco, previously oxidized by TEMPO, was boiled in an MXene solution at a temperature of 70°C. We tested the electrical properties of the resulting composite film, focusing on current density and specific capacitance. The measured current density values, corresponding to the different boiling times, were as follows: 0.000239 A/cm² for 30 minutes, 0.000307 A/cm² for 300 minutes, and 0.000320 A/cm² for 480 minutes. The specific capacitance values were 1.7005 F/g for 30 minutes, 1.9707 F/g for 300 minutes, and 2.0364 F/g for 480 minutes. The percentage increase in current density and specific capacitance values from 30 minutes to 300 minutes of boiling was 22% and 13.7%, respectively. For boiling from 300 to 480 minutes, the increase was 4.06% for current density and 3.22% for specific capacitance. These findings suggest that longer boiling times result in improved electrical properties. Subsequently, characteristic tests were performed, including XRD (X-ray diffraction) and SEM (Scanning Electron Microscope) analyses. The XRD results indicated that longer boiling times caused a rightward shift of the diffraction peak with a narrower peak width, signifying increased crystallinity. The highest X-ray intensity was observed in the composite boiled for 480 minutes, with a power of 847.23 counts per second (cps) and a two-theta angle of 21.31°. Additionally, the smallest crystal size was achieved with a 480-minute boiling time, measuring 138.2851 Å. In the SEM analysis, it was evident that longer boiling times led to a higher fraction of MXene within the composite film.
Enhancing Current Density and Specific Capacitance of Nata de Coco, TEMPO, and MXene Composites through Boiling Time Variations Yunus, Syukri; Umah, Kuntum Khairah; Abral, Hairul; Ogah, Ogah Anselm; Aulia, Aulia
Andalasian International Journal of Applied Science, Engineering and Technology Vol. 3 No. 3 (2023): November 2023
Publisher : LPPM Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/aijaset.v3i3.110

Abstract

This research aimed to enhance the current density and specific capacitance of electronic device materials to replace traditional metal materials. Composite materials that include Nata de Coco, TEMPO (2,2,6,6-tetramethylpiperidine-1-oxyl), and MXene achieve this improvement. Composite materials that include Nata de Coco, TEMPO, and MXene accomplish this improvement. Initial testing has shown that these materials initially demonstrated lower electrical properties, particularly in current density and specific capacitance, than conventional metals. To enhance their electrical properties, we employed a boiling method with variations in boiling time. The time intervals chosen were 30, 300, and 480 minutes. In the manufacturing process, Nata de Coco, previously oxidized by TEMPO, was boiled in an MXene solution at a temperature of 70°C. We tested the electrical properties of the resulting composite film, focusing on current density and specific capacitance. The measured current density values, corresponding to the different boiling times, were as follows: 0.000239 A/cm² for 30 minutes, 0.000307 A/cm² for 300 minutes, and 0.000320 A/cm² for 480 minutes. The specific capacitance values were 1.7005 F/g for 30 minutes, 1.9707 F/g for 300 minutes, and 2.0364 F/g for 480 minutes. The percentage increase in current density and specific capacitance values from 30 minutes to 300 minutes of boiling was 22% and 13.7%, respectively. For boiling from 300 to 480 minutes, the increase was 4.06% for current density and 3.22% for specific capacitance. These findings suggest that longer boiling times result in improved electrical properties. Subsequently, characteristic tests were performed, including XRD (X-ray diffraction) and SEM (Scanning Electron Microscope) analyses. The XRD results indicated that longer boiling times caused a rightward shift of the diffraction peak with a narrower peak width, signifying increased crystallinity. The highest X-ray intensity was observed in the composite boiled for 480 minutes, with a power of 847.23 counts per second (cps) and a two-theta angle of 21.31°. Additionally, the smallest crystal size was achieved with a 480-minute boiling time, measuring 138.2851 Å. In the SEM analysis, it was evident that longer boiling times led to a higher fraction of MXene within the composite film.
Enhancing Current Density and Specific Capacitance through Tensile TEMPO, Bacterial Cellulose and Polypirrole Nanocomposites Yunus, Syukri; Manurung, Muhammad Fajar Ruhud; Aulia, Aulia; Arief, Yanuar Zulardiansyah
Andalasian International Journal of Applied Science, Engineering and Technology Vol. 4 No. 1 (2024): March 2024
Publisher : LPPM Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/aijaset.v4i1.118

Abstract

The researchers developed a bio-composite film material that serves as a substitute for metal. The materials used are TEMPO ((2,2,6,6-tetramethylpiperidine-1-oxyl)), Bacterial Cellulose, and Polypyrrole (Ppy). This research aimed to increase the material's current density and specific capacitance values using the drawing method. Composite nanomaterials are made by oxidizing BC (Bacterial Cellulose) with TEMPO. The resulting TOBC (TEMPO Bacterial Cellulose) material was mixed with Ppy using the in situ method. The mixture is then drawn wet—measurement of current density and capacitance using Cyclic Voltammetry (CV) Testing. The current density and specific capacitance results increased by 542.74% and 754.79% after drawing the nanocomposite material. It is directly proportional to the effects of characteristic testing, which includes SEM, XRD, and FTIR. As a result of the withdrawal of the polypyrrole, it will be more evenly distributed in the composite material, absorbing and coating the nata de coco. The researchers concluded that when the TOBC/Ppy fibers are straighter and denser, they achieve higher current density and capacitance values.
An internet of things-based weather system for short-term solar and wind power forecasting using double moving average Syafii, Syafii; Nur Izrillah, Imra; Aulia, Aulia; Ilhamdi Rusydi, Muhammad
Bulletin of Electrical Engineering and Informatics Vol 14, No 5: October 2025
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/eei.v14i5.9852

Abstract

This article presents the design and implementation of an internet of things (IoT)-based weather forecasting system aimed at optimizing operational planning for renewable energy generation. The system leverages a Raspberry Pi as its central controller, integrating pyranometer and anemometer sensors for real-time data collection and predictive analytics. Utilizing the double moving average method, the system provides accurate short-term forecasts of solar and wind power outputs, which are crucial for addressing the intermittency challenges of renewable energy sources. The integration with the Blynk platform ensures user-friendly data visualization and accessibility. Results from a three-day testing phase reveal the system's high accuracy, with prediction errors of 8.79% for solar power and 16.49% for wind power. These findings underscore the system's potential to enhance energy planning, improve efficiency, and support sustainability goals. By enabling data-driven decision-making, this IoT-based forecasting system offers a scalable solution for advancing renewable energy integration into the power grid.
Solar power forecasting using a SARIMA approach for Indonesia's grid integration Ricky Maulana; Syafii Syafii; Aulia Aulia
International Journal of Power Electronics and Drive Systems (IJPEDS) Vol 17, No 1: March 2026
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/ijpeds.v17.i1.pp293-302

Abstract

Indonesia’s transition toward a renewable energy-dominated power grid is progressing to meet increasing energy demands while reducing dependence on fossil fuels. According to the National Energy General Plan, their goal is to have 23% of the energy mix come from renewables by 2025 and 31% by 2050. Accurate forecasting of photovoltaic (PV) power output is crucial to address the intermittent nature of solar energy and ensure grid stability. A seasonal autoregressive integrated moving average (SARIMA) model was developed to estimate day-ahead photovoltaic power output in Padang City, Indonesia. Using NASA solar irradiance data from March 1-31, 2024, the SARIMA(1,0,1)(4,0,3)24 model achieved high accuracy with an NRMSE of 4.19%. To evaluate its performance, a comparative evaluation was conducted between the SARIMA model and two machine learning methods, namely artificial neural network (ANN) and long short-term memory (LSTM), in which SARIMA achieved the lowest forecasting error. These findings indicate that SARIMA remains an effective and interpretable statistical method for short-term PV forecasting, supporting reliable energy planning and power grid operations towards Indonesia's renewable energy goals.
A framework for multi-interval optimal power flow under solar energy penetration Ricky Maulana; Syafii Syafii; Aulia Aulia
Bulletin of Electrical Engineering and Informatics Vol 15, No 2: April 2026
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/eei.v15i2.11091

Abstract

The increasing penetration of renewable energy introduces variability and uncertainty into power system operations, thus requiring accurate forecasting methods to ensure reliable and economical scheduling. This study presents a multi-interval day-ahead optimal power flow (OPF) analysis integrated with photovoltaic (PV) generation, where hourly PV forecasts are obtained using the seasonal autoregressive integrated moving average (SARIMA) (1,0,1)(4,0,3)24 model. The forecast results achieved low error values (root mean square error (RMSE)=0.354, normalized RMSE (NRMSE)=4.192%, mean absolute error (MAE)=0.202), successfully capturing the daily PV generation pattern and providing sufficiently accurate input for the OPF simulation. The forecasted PV profiles were then integrated into a multi-interval OPF framework using the MATPOWER interior point solver (MIPS) solver. Results show that PV integration reduces system operating costs compared to cases without PV, with cost savings observed at various time intervals (e.g., reduction from $802.22/hour to $780.65/hour during PV peak hours). Compared to the conventional single-interval OPF benchmark based on Weibull distribution assumptions for PV, the proposed framework achieves lower average costs ($790.97/hour vs. $869.70/hour) while also reflecting the real variability of solar dynamics and load. Overall, the integrated forecasting-optimization framework demonstrates that SARIMA-based PV forecasting provides reliable inputs for OPF and offers a practical tool to support future system planning and operation with higher renewable energy penetration.
Assessment of AEKF SoC Estimation in a LiFePO₄ Battery System with Relay Switching Control Imam Hidayat Usman; Syafii Syafii; Novizon Novizon; Aulia Aulia
PROtek : Jurnal Ilmiah Teknik Elektro Vol 13 No 2 (2026): Protek : Jurnal Ilmiah Teknik Elektro
Publisher : Program Studi Teknik Elektro Universitas Khairun

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33387/protk.v13i2.11204

Abstract

This study implements an Adaptive Extended Kalman Filter (AEKF) for real-time state of charge (SoC) estimation to support charge–discharge regulation in a LiFePO₄ battery system integrated with photovoltaic (PV) generation. Due to the variability of PV output, accurate and stable SoC estimation is essential for ensuring reliable battery operation. A first-order equivalent circuit model (1RC ECM) is employed to represent battery dynamics based on measured current and terminal voltage. The proposed AEKF algorithm is implemented on a Raspberry Pi 5 to enable real-time computation, and the estimated SoC is directly used as the control variable in a dual-relay switching mechanism to regulate charging and discharging processes. Experimental results show that the proposed method achieves a Mean Absolute Error (MAE) of 1.24% and a Root Mean Square Error (RMSE) of 1.58%, which are both below the 5% target specified in the system design. The system successfully maintains the battery within a safe SoC range of 57.5% to 85.2%, while ensuring stable relay operation without chattering under dynamic load and charging conditions. These results demonstrate that the proposed AEKF-based approach provides accurate, stable, and practical SoC estimation, making it suitable for real-time battery management in small-scale energy storage applications.