Claim Missing Document
Check
Articles

PENGARUH PERUBAHAN TERMINAL TEMPERATUR DIFFERENCE (TTD) DAN DARIN COOLER (DCA) FEED WATER HEATER TERHADAP PERFORMA PLTU MENGGUNAKAN SIMULASI CYCLE TEMPO 5.1 Yunita Djamalu; Romi Djafar; Syaiful Umela; Abd Rasyid Salim
Journal of Energy and Mechanical Engineering Vol. 1 No. 2 (2024): Journal of Energy and Mechanical Engineering (Juni)
Publisher : Fakultas Sains dan Teknologi - Universitas Nahdlatul Ulama Gorontalo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.62299/jeme.vi.9

Abstract

Feedwater heater (FWH) performance can be monitored periodically by reviewing the terminal temperature difference (TTD) and drain cooler approach (DCA) values. Monitoring this value by comparing the actual condition and the value resulting from commissioning.  The lower the TTD and DCA values, the better the work effectiveness of FWH. In general, the TTD value ranges between 2.8 ºC to -2.8 ºC while the DCA is between 5.6 ºC to 1 ºC. In this research, modeling was carried out using a cycle tempo simulation of the Molotabu Gorontalo 2 x 12.5 MW PLTU generator to review how much influence the changes in TTD and DCA values ​​of the low feedwater and hight feedwater heaters have. The variations used respectively are TTD with a value (°C) of 2.8; 2; 0; -2 and -2.8 while DCA) respectively (°C) 5.6; 5; 4 ; 3; 2 and 1. The aim of the research is to find out how heat transfer occurs in the two FWHs resulting from modeling and its effect on the Net Plant Hear Rate (NPHR) and the efficiency of the PLTU system. Based on the simulation results obtained using variations of TTD and DCA on the low feedwater heater, the heat transfer in the heater is 144830 kW and 1761.48 kW. Meanwhile, the high feedwater heater produces heat transfer to the heater of 3400.13 kW and 3795.24 kW. As for energy balance, the lowest gross power was 26.32% and the highest was 26.5%. Based on the analysis results, the highest NPHR value was 21634.24 kg/kJ/h, getting an efficiency value of 25.87%. while the lowest NPHR is 25130.43 kg/kJ/h low NPHR produces the highest efficiency of 26%.
PERANCANGAN FILTER AIR LAUT MENJADI AIR TAWAR MENGGUNAKAN ENERGI SURYA MODEL PIRAMIDA DENGAN METODE REVERSE OSMOSIS Alpandi Dama; Yunita Djamalu; Romi Djafar; Syaiful Umela; Rian Kadir
Journal of Energy and Mechanical Engineering Vol. 2 No. 1 (2024): Journal of Energy and Mechanical Engineering (Desember)
Publisher : Fakultas Sains dan Teknologi - Universitas Nahdlatul Ulama Gorontalo

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

ABSTRACT The lack of clean water is a serious problem that needs to find a solution, namely by utilizing sea water which is available in large quantities to produce clean and salty water. The best solution to this problem is seawater desalination. The human reproductive system is not a new technology. Therefore, in the research explaining the design of a sea water filter into fresh water using pyramid model solar energy using the reverse osmosis method, this research carried out comprehensive testing of the quality of fresh water produced by the distillation equipment, including to determine pH levels, conductivity, turbidity, TDS, color, smell, and taste. Meanwhile, previous research did not test the quality of the water produced. The research results obtained from testing the parameters of odor, taste and color in seawater samples showed that there was no odor, no taste and no color in the distilled water samples. Keywords: Design, Sea Water, Reverse Osmosis
ANALISIS TERMODINAMIKA SISTEM PLTU ANGGREK KAPASITAS 2X25 MW MENGGUNAKAN BAHAN BAKAR CO-FIRING BIOMASSA: ANALISIS TERMODINAMIKA SISTEM PLTU ANGGREK KAPASITAS 2X25 MW MENGGUNAKAN BAHAN BAKAR CO-FIRING BIOMASSA lilis karim; Romi Djafar; Rian Kadir; Yunita Djamalu; Moh. Riyandi Badu
Journal of Energy and Mechanical Engineering Vol. 3 No. 1 (2025): Journal of Energy and Mechanical Engineering (Desember)
Publisher : Fakultas Sains dan Teknologi - Universitas Nahdlatul Ulama Gorontalo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.62299/jeme.v3i1.18

Abstract

Coal-fired power plants (PLTUs) play a crucial role in the national electricity system due to their ability to generate electricity on a large scale. The 2x25 MW Anggrek Steam Power Plant in North Gorontalo Regency is one of the power plants that has implemented Lamtoro biomass cofiring technology. This study aims to analyze the thermodynamic performance of the 2x25 MW Anggrek Steam Power Plant (PLTUs) under two conditions: existing (100% coal) and cofiring (85% coal + 15% lamtoro biomass). The method employed in this study utilizes thermodynamic law analysis, supplemented by cycle tempo simulations, to evaluate boiler and power cycle efficiency. The results show boiler efficiency under cofiring conditions of 82.45% (direct method) and 87.04% (heat duty method). The power cycle efficiency decreased from 23.336% (existing) to 21.652% (cofiring) due to the lower heating value of the biomass. Therefore, despite the decrease in efficiency, cofiring lamtoro biomass remains a feasible alternative fuel in PLTUs because it can maintain operational stability and has the potential to reduce carbon emissions.
PEMODELAN SISTEM PLTU ANGGREK 2 X 25 MW MENGGUNAKAN SOFTWARE CYCLE TEMPO DENGAN BAHAN BAKAR CO-FIRING BATUBARA DAN LAMTORO: PEMODELAN SISTEM PLTU ANGGREK 2 X 25 MW MENGGUNAKAN SOFTWARE CYCLE TEMPO DENGAN BAHAN BAKAR CO-FIRING BATUBARA DAN LAMTORO Rizki Mohamad; Romi Djafar; Rian Kadir; Yunita Djamalu; Syaiful Umela
Journal of Energy and Mechanical Engineering Vol. 3 No. 1 (2025): Journal of Energy and Mechanical Engineering (Desember)
Publisher : Fakultas Sains dan Teknologi - Universitas Nahdlatul Ulama Gorontalo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.62299/jeme.v3i1.19

Abstract

As Indonesia's population grows, the need for electrical energy increases. To meet this demand, the government is required to build power plants, one of which is a Steam Power Plant (PLTUs). However, PLTUs still rely on coal as their primary fuel, which contributes significantly to carbon emissions. One effort to reduce these emissions is the implementation of biomass cofiring technology as a more environmentally friendly alternative energy source. This study aims to model the thermal system of the Anggrek 2×25 MW PLTUs using Cycle Tempo 5.0 software and evaluate the system performance at varying cofiring ratios of coal with lamtoro biomass, specifically 10%, 15%, 20%, 25%, and 30%. The research method employed a cycle tempo simulation, utilizing input parameters derived from the actual operational data of the Anggrek PLTUs. The system model built was used to compare the performance of the PLTUs under existing conditions with various fuel mixture variations. The simulation results showed that the addition of lamtoro biomass to the fuel mixture reduced the efficiency of the thermal system due to the lower heating value of biomass compared to coal. The results based on existing conditions of 100% coal provided the highest efficiency, namely gross power of 23.23% and net power of 22.23%. At the same time, the 10% cofiring variation achieved a gross power efficiency of 21.98% and a net power of 21.02%. Meanwhile, a 15% variation yielded a gross power of 21.32% and a net power of 20.37%. Furthermore, a 20% variation yielded a gross power of 21.00% and a net power of 20.03%. A 25% variation yielded a gross power of 20.56% and a net power of 19.61%. Finally, a 30% variation yielded a gross power of 20.31% and a net power of 19.36%. Thus, this study demonstrates that cofiring lamtoro biomass can be a strategy to reduce dependence on coal and reduce carbon emissions, although system efficiency tends to decrease.
PERANCANGAN ALAT PENCETAK BRIKET SISTEM PNEUMATIK DAN PENGUJIANNYA Haeril Ikram; Yunita Djamalu; Syaiful Umela; Romi Djafar; Rian Kadir
Journal of Energy and Mechanical Engineering Vol. 3 No. 1 (2025): Journal of Energy and Mechanical Engineering (Desember)
Publisher : Fakultas Sains dan Teknologi - Universitas Nahdlatul Ulama Gorontalo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.62299/jeme.v3i1.21

Abstract

The growing demand for energy has led to the exploration of renewable resources as alternatives to fossil fuels. Coconut shells, as a type of biomass, are highly potential to be processed into briquettes. This study focuses on designing and testing a pneumatic-based briquette press to produce briquettes that meet quality requirements. An experimental method was applied, consisting of tool design, fabrication, and performance testing. The results indicated that the single-acting pneumatic press was capable of producing 10 square briquettes per cycle with an average time of approximately one minute. The compressive strength ranged from 14.553 to 17.410 kN, which complies with Indonesian National Standard (SNI) and demonstrates good briquette density. Moisture content values were recorded between 2.4% and 7.7%, still below the maximum threshold of 8% based on SNI 01-6235-2000. Combustion tests showed that the briquettes could burn for up to 90 minutes with a peak temperature of around 120°C. The use of pneumatic technology provided faster production, more uniform shapes, and lower energy consumption compared to manual processes. Therefore, this machine has significant potential to promote environmentally friendly and sustainable alternative energy use.
RANCANGAN BANGUN UJI KINERJA TUNGKU PEMANGGANG MENGGUNAKAN BAHAN BAKAR GAS : RANCANGAN BANGUN UJI KINERJA TUNGKU PEMANGGANG MENGGUNAKAN BAHAN BAKAR GAS Astri Mulya Sukarti Kaino; Yunita Djamalu; Syaiful Umela; Romi Djafar; Riyandi Badu
Journal of Energy and Mechanical Engineering Vol. 3 No. 1 (2025): Journal of Energy and Mechanical Engineering (Desember)
Publisher : Fakultas Sains dan Teknologi - Universitas Nahdlatul Ulama Gorontalo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.62299/jeme.v3i1.22

Abstract

Permasalahan yang sering terjadi pada tungku pemanggang berbahan bakar arang adalah sulitnya mengontrol suhu, tingginya produksi asap, serta efisiensi pembakaran yang rendah. Penelitian ini bertujuan untuk merancang bangun dan menguji kinerja tungku pemanggang menggunakan bahan bakar gas sebagai solusi yang lebih efisien dan ramah lingkungan.Metode yang digunakan adalah metode eksperimen teknik dengan tahap: perancangan alat, pembuatan tungku, pengujian kinerja alat, serta analisis data. Parameter yang diamati meliputi waktu penyalaan, suhu pemanggangan, konsumsi bahan bakar, efisiensi termal, dan kadar air ikan sebelum dan sesudah pemanggangan. Selain itu, dilakukan perbandingan kinerja tungku antara tungku gas dan tungku arang.Hasil pengujian menunjukkan bahwa waktu penyalaan tungku gas hanay membutuhkan ±8 detik dengan suhu stabil 100°C dalam waktu 10 menit. Konsumsi gas 0,34 kg selama 28 menit. Perbandingan dengan tungku arang menunjukkan bahwa tungku gas lebih unggul dalam waktu, kontrol suhu, dan efisiensi pembakaran. Kesimpulan dari penelitian ini adalah bahwa tungku pemanggang berbahan bakar gas lebih efisien, cepat, dan ramah lingkungan dibandingkan dengan tungku berbahan bakar arang. Alat ini cocok digunakan oleh pelaku usaha kecil dibidang makanan panggang
DARI LIMBAH HETEROGEN MENUJU BIOREFINERY TERINTEGRASI: KONVERGENSI JALUR TERMOKIMIA–BIOLOGIS, PRODUK BERNILAI TAMBAH, DAN KELAYAKAN BERKELANJUTAN Hariadi Hariadi; Romi Djafar
Journal of Energy and Mechanical Engineering Vol. 3 No. 2 (2026): Journal of Energy and Mechanical Engineering (Juni)
Publisher : Fakultas Sains dan Teknologi - Universitas Nahdlatul Ulama Gorontalo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.62299/jeme.v3i2.38

Abstract

Transisi dari pengelolaan limbah menuju biorefinery menuntut kerangka yang mampu menghubungkan keragaman bahan baku, pilihan teknologi, mutu produk, dan kelayakan sistem. Tinjauan ini mensintesis 51 publikasi tahun 2022–2026 mengenai biomassa lignoselulosa, alga, lumpur, residu perikanan, limbah pangan, dan campuran biomassa–plastik. Analisis difokuskan pada pencernaan anaerobik dan fermentasi, pirolisis, torrefaksi, gasifikasi, pencairan hidrotermal, koproses, produksi hidrogen, biochar, serta pemulihan produk bernilai tambah. Sintesis menunjukkan bahwa tidak ada jalur konversi tunggal yang unggul untuk semua bahan baku. Kadar air tinggi mendukung proses hidrotermal dan biologis, sedangkan biomassa kering lebih sesuai untuk pirolisis, gasifikasi, dan densifikasi. Pretreatment, katalisis, gelombang mikro, ko-konversi, serta penggabungan aliran produk dapat memperbaiki hasil dan mutu, tetapi manfaat tersebut sering dibayar dengan kebutuhan energi, bahan kimia, hidrogen, atau pemurnian yang lebih besar. Bukti terbaru menggeser ukuran keberhasilan dari rendemen bahan bakar semata menuju portofolio produk, sirkularitas nutrien, penurunan toksisitas, efisiensi eksergi, jejak karbon, dan ketahanan ekonomi. Sistem paling menjanjikan menggunakan desain bertingkat: fraksinasi atau ekstraksi produk bernilai tinggi di bagian hulu, konversi energi pada residu, pemanfaatan char atau digestate, dan daur ulang panas, air, serta nutrien. Tinjauan ini mengusulkan matriks keputusan berbasis karakter bahan baku dan hierarki nilai untuk menyelaraskan pemilihan teknologi dengan indikator teknis, ekonomi, lingkungan, dan kesiapan skala. Agenda riset prioritas meliputi standarisasi data, uji jangka panjang, analisis ketidakpastian, integrasi penilaian daur hidup–tekno ekonomi, dan demonstrasi sistem modular pada konteks regional. Kerangka tersebut membantu peneliti dan pengembang menghindari optimasi parsial, membandingkan opsi secara transparan, serta memilih konfigurasi yang sesuai dengan sumber daya dan pasar setempat secara lebih konsisten.
BIOCHAR MULTIFUNGSI DALAM EKONOMI SIRKULAR: REKAYASA PROSES, HUBUNGAN STRUKTUR–FUNGSI, DAN JALUR IMPLEMENTASI UNTUK ENERGI, LINGKUNGAN, PERTANIAN, SERTA MATERIAL MAJU syamsu Akuba; Romi Djafar; Abd. Rasid Salim
Journal of Energy and Mechanical Engineering Vol. 3 No. 2 (2026): Journal of Energy and Mechanical Engineering (Juni)
Publisher : Fakultas Sains dan Teknologi - Universitas Nahdlatul Ulama Gorontalo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.62299/jeme.v3i2.42

Abstract

Biochar has evolved from a biomass carbonization product into an engineered material platform for carbon storage, energy, remediation, agriculture, and composite applications. However, recent literature remains fragmented across sectors, leaving the relationships among feedstocks, conversion conditions, structure, function, and sustainability impacts insufficiently understood. This review synthesizes the bibliographic records and abstracts provided in the reference dataset through title- and DOI-based deduplication, thematic relevance screening, and a comparative analysis of studies published over the past five years. The analysis is structured around a feedstock–process–structure–function–impact framework. The results show that temperature, residence time, atmosphere, heating rate, and activation govern the trade-offs among carbon yield, aromatization, surface functional groups, porosity, reactivity, and process emissions. Unmodified biochar is adequate for certain fuel and soil amendment applications, whereas pollutant and carbon dioxide capture, catalysis, energy storage, and composite reinforcement generally require surface engineering or hybrid architectures. Field evidence indicates that the optimum application rate is nonlinear and depends on the specific biochar–soil–plant combination; increasing the application rate does not necessarily produce greater benefits. In water treatment, laboratory adsorption capacity alone is insufficient to demonstrate feasibility because regeneration, leaching, ion competition, reactor configuration, and cost determine actual performance. This review proposes an intended-use-based biochar quality passport, tiered testing from the material to the system level, and life-cycle assessment that accounts for the product’s end-of-life fate. The novelty of this synthesis lies in integrating applications that are commonly examined separately and establishing a decision-making framework for matching biochar properties with their intended functions, risks, and implementation scales. This approach helps prevent universal claims and directs research toward long-term demonstration, standardization, and industrial integration that can be verified technically, economically, and environmentally across different regions.
Studi Pemanfaatan Limbah PLTU (Pembangkit Listrik Tenaga Uap) FABA (Fly Ash Dan Bottom Ash) Sebagai Bahan Aditif Dalam Pembuatan Batako: Study On The Utilisation Of FABA (Fly Ash And Bottom Ash) Waste From Steam Power Plants As Additives In The Manufacture Of Concrete Blocks Rifansa Bintan; Romi Djafar; Rustam Anwar
Journal of Environmental Engineering Research Vol. 3 No. 2 (2025): Journal of Environmental Engineering Research
Publisher : Fakultas Sains dan Teknologi - Universitas Nahdlatul Ulama Gorontalo

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

PT PLN (Persero) merupakan PT yang memastikan pasokan energi yang memadai untuk mendukung pertumbuhan ekonomi dan kesejahteraan masyarakat Indonesia. Penelitian ini adalah sebagai bahan uji coba dalam penggunaan limbah PLTU (Pembangkit Listrik Tenaga Uap) FABA (fly ash dan bottom ash) sebagai bahan tambahan tambahan dalam pembuatan batako. Metode yang digunakan dalam penelitian ini adalah metode eksperimen dengan persentase proporsi 3 campuran FABA dan 1 campuran tanpa FABA yaitu pada spesimen 1 fly ash 15%, bottom ash 20%, pasir 40%, semen 15%, air 10%, spesimen 2 fly ash 20%, bottom ash 15%, pasir 40%, semen 15%, air 10% dan spesimen 3 fly ash 10%, bottom ash 25%, pasir 40%, semen 15%, air 10%, untuk spesimen tanpa FABA yaitu pasir 65 %, semen 15% dan air 10%. Dari 3 variasi FABA itu mengahasilkan kuat tekan dan daya serap air tertinggi yaitu pada spesimen 3, untuk kuat tekannya sebesar 93,42 kg/cm2 dan daya serap airnya sebesar 13,32 %, dibandingakan dengan Batako tanpa FABA hanya menghasilkan daya serap air 15,62 % dan kuat tekan 85,26 kg/cm2. Tetapi masih memenuhi syarat kuat tekan mutu II berdasarkan SNI 03-0349-1989.
THERMAL MANAGEMENT AT THE ENERGY WATER ENVIRONMENT NEXUS: FROM PHOTOTHERMAL MATERIALS AND BUILDING ENVELOPES TO GRIDRESPONSIVE ENERGY SYSTEMS Yunita Djamalu; Romi Djafar; Siti Fauziah; Roys Pakaya
Journal Of Renewable Energy Engineering Vol. 3 No. 2 (2025): Journal Of Renewable Energy Engineering (Oktober)
Publisher : Program Vokasi-Universitas Negeri Gorontalo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.56190/jree.v3i2.61

Abstract

Thermal phenomena sit at the heart of today’s most important sustainability challenges, producing clean water, maintaining healthy indoor climates, valorizing biomass, and balancing increasingly variable power grids. This review synthesizes state-of-the-art advances across materials, devices, buildings, and energy systems to outline an integrated research agenda for the energy–water–environment nexus. We highlight photothermal platforms for desalination and wastewater treatment, including macroporous three-dimensional MXene architectures with high broadband absorption and near-complete contaminant rejection, a nature-inspired “suspended” evaporator that resists salt accumulation even in 15–20 wt% brines, and scaling-mitigating slippery membranes for robust membrane distillation (Lan, Wood, & Yuen, 2019), (Zhao et al., 2019), (Islam et al., 2020). For the built environment, we analyze optimization of phase-change Trombe walls, localized solid-state humidity pumping, evidence-based thermal comfort indices, and holistic multi-objective design of net-zero energy housing in the tropics (Zhang et al., 2022; Tumuluru, Ghiasi, Soelberg, & Sokhansanj, 2021), (Luo et al., 2021; Mani et al., 2023). On the supply side, we assess rapid load transitions in solid-oxide-fuel-cell–gas-turbine hybrids, optimization-driven power-flow management, and thermal-pollution constraints on water-cooled generation (Staiger, Laschewski, & Matzarakis, 2019),(Zhu et al., 2021; Li, Hua, Tu, & Wang, 2019). Finally, we connect circular carbon strategies torrefaction and biochar to both energy quality and environmental remediation (Karanikola, Boo, Rolf, & Elimelech, 2018), (Miara et al., 2018). We conclude with cross-cutting gaps in durability, field validation, and multi-scale modeling, and propose harmonized metrics and standardized protocols to accelerate translation. All citations derive from the user-provided corpus.