Claim Missing Document
Check
Articles

Found 29 Documents
Search

Performance of Groundplane Shaping in Four-Element Dualband MIMO Antenna Subuh Pramono; Tommi Hariyadi; Budi Basuki Subagio
TELKOMNIKA (Telecommunication Computing Electronics and Control) Vol 15, No 1: March 2017
Publisher : Universitas Ahmad Dahlan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12928/telkomnika.v15i1.5002

Abstract

This work presents performance of groundplane shaping and its effect in four element dualband multiple input multiple output (MIMO) antenna. This proposed four element dualband MIMO antenna consists of four bowtie dipole antenna which operates at 1800 MHz (low frequency) and 2300 MHz (high frequency). This proposed four element dualband MIMO antenna occupies a 270 x 210 x  100 mm3  of FR 4 substrate. We use four types  of groundplane pattern i.e. full groundplane, cornered spatial groundplane,crossed middle groundplane, and spiral groundplane. These various grounplane patterns influence the performance of main parameters of dualband MIMO antenna. Cornered spatial groundplane pattern yields a largest bandwidth (VSWR ≤ 2) 282 MHz or 15.24% of center frequency at low frequency. Full groundplane pattern creates 135.2 MHz at high frequency. In addition, cornered spatial groundplane pattern also generates a lowest VSWR  that  is valued 1.21 at both low frequency and high frequency. The S parameters, basically both cornered spatial and full groundplane pattern produce a better return loss than two others. All four groundplane patterns deliver  equally a mutual coupling parameter.The last, this proposed four element dualband MIMO with various groundplane patterns gives a good farfield properties i.e. gain, radiation pattern, H-E field.
Performance of Channel Estimation in MIMO-OFDM Systems Subuh Pramono; Eddy Triyono
TELKOMNIKA (Telecommunication Computing Electronics and Control) Vol 11, No 2: June 2013
Publisher : Universitas Ahmad Dahlan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12928/telkomnika.v11i2.937

Abstract

 This paper presented the performance of faded channel estimation method on orthogonal frequency division multiplexing-multiple input multiple outputs (OFDM-MIMO) i.e. least squares (LS) and minimum mean squared error (MMSE). Channel impuls response (CIR) was  required to overcome the intersymbol interference (ISI). Channel impuls response information was obtained from channel estimation processing. Iterance simulation used monte-carlo technique to determine the performance of bit error rate (BER) and mean squared error (MSE). Simulation results show that the mean squared error performance on MIMO system was better than the SISO system. On MMSE channel estimation, the MIMO 2Tx-2Rx system provided ± 2 dB improvement that compared to SISO system at value of MSE 10-2.Furthermore,MIMO 3Tx-2Rx produce improvement about 1.5 dB, MIMO 4Tx-2Rx improve about 3.5 dB at BER 10-4,respectively.The MIMO 2Tx-2Rx system, MMSE channel estimation produced better performance ± 1 dB than LS channel estimation with sufficient SNR value for MSE 10-2 .Pilot arrangement, the simulation results show that the block type-pilot arrangement produced better performance than the comb type-pilot arrangement at fast fading channel. Block type-pilot arrangement system produced better ± 10 dB than the comb type-pilot arrangement with MMSE method at value of BER 2 10-2. 
Comparative Performance Analysis of Linear Precoding in Downlink Multi-user MIMO Subuh Pramono; Eddy Triyono
Proceeding of the Electrical Engineering Computer Science and Informatics Vol 5: EECSI 2018
Publisher : IAES Indonesia Section

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (440.782 KB) | DOI: 10.11591/eecsi.v5.1638

Abstract

This paper investigates the comparative performance of linear precoding schemes. The linear precoding schemes are including block diagonalization (BD), zero forcing (ZF), and maximum ratio transmission (MRT) in downlink multi-user MIMO. This work delivers the performance of linear precoding in term of achievable sum rate and bit error rate (BER) with a variation of the signal to noise ratio (SNR) and the number of transmitter-receiver antennas. We suppose that the transmitters have a complete channel state information. The results show that the MRT precoding yields better bit error rate than both the BD and ZF precoding schemes. However, the ZF precoding generates better achievable sum rate than the MRT precoding. In the other side, the MRT precoding also outperforms when the number of active users is bigger than Kcross while the number of active users is less than Kcross the ZF precoding is still dominant.
Performance Analysis of SM-MISO with Q-CSIT in Wireless Sensor Network Subuh Pramono; Muhammad Ibrahim; Feri Adriyanto; Alfin Hikmaturokhman
Proceeding of the Electrical Engineering Computer Science and Informatics Vol 6: EECSI 2019
Publisher : IAES Indonesia Section

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/eecsi.v6.1986

Abstract

In this paper, we investigate the role of Q-CSIT in SM-MISO for wireless sensor networks system. The SN are connected to the CH, it is modeled as a MISO system. Spatial modulation has an advantage over a conventional MIMO system which does not require multiple radio frequency chains as many as the number of transmit antennas. The Q-CSIT is aimed to estimate the faded wireless channel with a limited/finite number of bits. The finite number of feedback bits trigger the SN adapt automatically its AMC modes. Adaptation of the AMC modes causes a changing of transmit power and transmission rate, these changes will make a better probability of error. The numerical results show that bigger the number of feedback bits yields better SER. Furthermore, lower spatial correlation generates a better probability of error. The last, quality of wireless channel that is stated in SNR also dominantly influences the performance of SM – MISO system.
SISTEM PROTEKSI OVER CURRENT RELAY MOTOR FORCED DRAFT FAN PADA PEMBANGKIT LISTRIK TENAGA UAP Aulia Vici Yunitasari; Subuh Pramono
Jurnal Teknologi Vol 13, No 1 (2021): Jurnal Teknologi
Publisher : Fakultas Teknik Universitas Muhammadiyah Jakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24853/jurtek.13.1.55-62

Abstract

side the power plant uses an electric motor as equipment to convert electrical energy into mechanical, which uses a 3 phase motor. The Steam Power Plant has FDFan which functions as a device that supplies or forces outside air into the boiler combustion chamber. If the power plant operates, there will certainly be many disruptions which will occur due to several factors. Each motor has its own protection system. Especially on the FDfan 3A motor at the PLTU has several protection systems, including Over Current Relay as protection from overcurrent resulting in short circuit current, then Overload Relay as overload protection. In this report, mathematically analyzing calculations and comparing to determine the starting motor current and pick up current in the relay when under normal conditions or in trip conditions. At the power plant unit 3 FDFan motor with a power of 1722 kW produces a starting motor current of 118 A at the test value and the value of the mathematical calculation of 108.86 A. While the overcurrent relay with a pick up value of 4 A and the value of the mathematical calculation of 4.08 A which can be said to be still relatively normal and in good condition. Overcurrent protection relay is needed on the FDFan motor to prevent overcurrent, it is necessary to adjust the current according to the nameplate so that the motor is working optimally.
Nutrient Uptake, Partitioning, and Production of Two Subspecies of Brassica using Different Solution Concentrates in Floating Hydroponics Systems Mercy Bientri Yunindanova; Subuh Pramono; Muhammad Hamka Ibrahim
Buletin Agroteknologi Vol 1 No 2 (2020): December
Publisher : Universitas Prof. Dr. Hazairin SH

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (716.805 KB) | DOI: 10.32663/ba.v1i2.1810

Abstract

In this study, we investigated nutrient uptake, partitioning, and production of two subspecies of Brassica in response to nutrient solution concentration in floating hydroponics systems. This study used a complete randomized block design factorial with two factors. The first factor was two Brassica subspecies consisting of Brassica rapa subsp. chinensis (Pak Choi) and Brassica rapa var. parachinensis (Choy Sum). The second factor was the concentration level consisting electrical conductivity (EC) 1 mS cm-1 and EC 2 mS cm-1. The results indicated the absorption rates of nitrogen (N,) phosphorus (P), and potassium (K) in leaves, roots and stems were similar in both nutrient concentrations. In general, all combination treatments resulted more accumulation of P followed by N, also K as the smallest proportion. P was mostly accumulated at the root and leaves (19.60 to 25.90 mg g-1), while majority of N was collected in leaves ranging from 18.00 to 24.30 mg g-1. The highest K content was detected in the stem (10.70 to 14.20 mg g-1). P uptake was 1.69 to 2.47 times higher than K, while N uptake was 1.44 to 2.04 times higher than K. Both two subspecies and concentrations performed no significant effects on nutrient uptake. Although same species, the plant growth parameters of Pak Choi and Choy Sum are very different including plant height, leaves number, width and length. Both two subspecies adapted well with both concentrations. However, significant differences were recorded in the combination of subspecies and nutrient concentration on plant growth and production parameters. To achieve higher market portion, Pak Choi would be more suitable to be planted on EC 1 mS cm-1, while Choy Sum was favorable at both concentrations.
An Analysis of Quality of Service (QoS) In Live Video Streaming Using Evolved HSPA Network Media Achmad Zakaria Azhar; Subuh Pramono; Eko Supriyanto
JAICT Vol 1, No 1 (2016)
Publisher : Politeknik Negeri Semarang

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (529.17 KB) | DOI: 10.32497/jaict.v1i1.423

Abstract

Evolved High Speed Packet Access (HSPA+) is a mobile telecommunication system technology and the evolution of HSPA technology. This technology has a packet data based service with downlink speeds up to 21.1 Mbps and uplink speed up to 11.5 Mbps on the bandwidth 5MHz. This technology is expected to fulfill and support the needs for information that involves all aspects of multimedia such as video and audio, especially live video streaming. By utilizing this technology it will facilitate communicating the information, for example to monitoring the situation of the house, the news coverage at some certain area, and other events in real time. This thesis aims to identify and test the Quality of Service (QoS) performance on the network that is used for live video streaming with the parameters of throughput, delay, jitter and packet loss. The software used for monitoring the data traffic of the live video streaming network is wireshark network analyzer. From the test results it is obtained that the average throughput of provider B is 5,295 Kbps bigger than the provider A, the average delay of provider B is 0.618 ms smaller than the provider A, the average jitter of provider B is 0.420 ms smaller than the provider A and the average packet loss of provider B is 0.451% smaller than the provider A.
Analysis of Triple Quantum Dots Single Electron Transistor (TQD-SET) for Various Configuration Stephanus Hanurjaya; Miftahul Anwar; Meiyanto Eko Sulistyo; Irwan Iftadi; Subuh Pramono
Journal of Electrical, Electronic, Information, and Communication Technology Vol 2, No 2 (2020): JOURNAL OF ELECTRICAL, ELECTRONIC, INFORMATION, AND COMMUNICATION TECHNOLOGY
Publisher : Universitas Sebelas Maret (UNS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.20961/jeeict.2.2.44840

Abstract

Single electron transistor (SET) has high potential for the development of quantum computing technologies in order to provide low power consumption electronics. For that purpose, many studies have been conducted to develop SET using dopants as quantum dots (QD). The working principle of SET basically is a single electron tunneling one by one through tunnel junction based on the coulomb blockade effect. This research will simulate various configurations of triple quantum dots single electron transistors (TQD-SET) using SIMON 2.0 with an experimental approach of MOSFET with dopants QD. The configurations used are series, parallel, and triangle configuration. The mutual capacitance (Cm), tunnel junctions (TJ), and temperature values of TQD-SET configurations are varied. The I-V characteristics are observed and analyzed for typical source-drain voltage (Vsd). it is found that the TQD series requires larger Vsd than parallel or triangular TQDs. On the other hands, the current in parallel TQD tends to be stable even though Cm is changed, and the current in the TQD triangle is strongly influenced by the Cm. By comparing these three configurations, it is observed that the tunnelling rate is higher for parallel TQD due to higher probability current moves through three dots by applying Vds.
ROI based Indonesian Paper Currency Recognition Using Canny Edge Detection Ahmad Imam Rauyani; Muhammad Hamka Ibrahim; Subuh Pramono
Journal of Electrical, Electronic, Information, and Communication Technology Vol 2, No 1 (2020): JOURNAL OF ELECTRICAL, ELECTRONIC, INFORMATION, AND COMMUNICATION TECHNOLOGY
Publisher : Universitas Sebelas Maret (UNS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.20961/jeeict.2.1.41349

Abstract

Paper currency recognition is important for automatic payment system. The paper performs a nominal paper detection process using image processing with canny method implemented in python programming language. The canny method is used to find edge features in the nominal currency. By using template matching of image reference, region of interest (ROI) of nominal value is extracted so that it can be used in any orientation of  paper currency image. The ROI of nominal image is processed by canny edge method and spatial transformation to strengthen the image features and being processed by template matching to decide nominal currency. The study has successfully tested nominal value of 1000, 2000, 5000, 10000, 20000, 50000, and 100000 Indonesia banknotes which then the currency value will appear in the value variable in python.
Investigation of Cellular Base Transmitter Station Power Radiation using Spectrum Analyzer Muhammad Hamka Ibrahim; Subuh Pramono
Journal of Electrical, Electronic, Information, and Communication Technology Vol 4, No 1 (2022): JOURNAL OF ELECTRICAL, ELECTRONIC, INFORMATION, AND COMMUNICATION TECHNOLOGY
Publisher : Universitas Sebelas Maret (UNS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.20961/jeeict.4.1.57133

Abstract

The development of information and communication technology has spurred the development of the world of telecommunications. The development of telecommunications can be seen from the number of cellular service users supported by technological infrastructure in the form of BTS (Base Transmission Station). But in its development, there are social problems in the form of resistance from the community around BTS, one of the things that people worry about is the danger of radiation from BTS. This could be due to a lack of socialization and knowledge from the community. This study aims to provide education as well as quantitative evidence regarding radiation from BTS in Bulakrejo which is compared with safety standards from International Commission on Non-Ionizing Radiation Protection (ICNIRP) and Ministry of Communication and Information Indonesia. The result of investigation shows that received Power Radiation in near Base Station is safe according to regulatory standard.