Claim Missing Document
Check
Articles

PENGURANGAN CACAT ASSEMBLY MODEL M370 DENGAN PENDEKATAN RCA (ROOT CAUSE ANALYSIS) DAN FTA (FAULT TRR ANALYSIS) (STUDI KASUS : PT.SHIMANO BATAM) Vera Methalina Afma; Abdulah Merjani; Fadila Puspita Ayu
SIGMA TEKNIKA Vol 6, No 1 (2023): SIGMATEKNIKA, VOL. 6, N0. 1, JUNI 2023
Publisher : Fakultas Teknik, Universitas Riau Kepulauan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33373/sigmateknika.v6i1.5151

Abstract

PT. Shimano Batam Manufacturing (SBM) adalah perusahaan yang bergerak dalam bidang manufactur yang menghasilkan produk sperpart sepeda, salah satu Departeman PT. Shimano Batam Manufactur (SBM) adalah Departeman Front Derailleur (FD) merupakan sistem mekanis yang menggeser rantai pada sepeda dengan lebih dari satu chainring depan. Produk yang dihasilkan adalah M370, M310, M2000 dan TX 800. Penelitian ini bertujuan untuk mengetahui jenis cacat produk terbesar yang dihasilkan oleh line produksi, faktor utama penyebab dan perbaikan yang dilakukan untuk mengurangi cacat pada line prooduksi.Penelitian ini menggunakan Metode Root Cause Analysis (RCA) dan Faul Tree Analysis (FTA). Setelah melakukan penelitian diperoleh hasil bahwa jenis reject tertinggi adalah Banding Chain Guid. Sebelum melakukan penelitian ini jumlah reject pada Banding Chain Guid sebesar 1.4% dan setelah dilakukan penelitian jumlah reject turun menjadi 0.58%. 
Penerapan Proses Integrasi Kegiatan Pemindahan Hasil Rebusan Sari Kedelai Ke Bak Penyaringan Pabrik Tahu Di Batam (Studi Kasus Pabrik Tahu Pak Joko Dan Pak Udin) Siboro, Benedikta Anna Haulian; Afma, Vera Methalina; Sulaiman, Mohamad
Jurnal Sistem Teknik Industri Vol. 20 No. 2 (2018): JSTI Volume 20 Number 2 July 2018
Publisher : TALENTA Publisher

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (630.268 KB) | DOI: 10.32734/jsti.v20i2.489

Abstract

Pabrik tahu Pak Udin dan Pak Joko adalah pabrik pembuat tahu yang seluruh proses dilakukan secara manual, khususnya di bagian pemindahan sari kedelai dari bak rebus ke bak saring. Berat beban yang diangkat adalah ± 30 kg dengan suhu 85-90oC dan repetisi sebanyak 30 kali. Hal tersebut melebihi batas angkat yang di tetapkan oleh NIOSH yaitu 24.5 Penelitian ini bertujuan untuk melakukan perbaikan proses dengan menerapkan proses terintegrasi pada bak perebusan dan bakpenyaringan agar dapat mengeliminasi proses angkat dan meningkatkan efesiensi waktu dengan menggunakan metode Ovako Work Analysis System, Antropometri dengan postur kerja berdiri dan jam henti. Hasil data OWAS meenunjukkan bahwa postur tubuh pengangkatan air rebus kedelai berbahaya bagi kesehatan dan keselamatan pekerja (nilai OWAS yang diperoleh 3,5). Selanjutnya desain dikembangkan dengan mengintegrasikan stasiun bak perebusan dan penyaringan menggunakan mesin pompa dan pipa penghubung sehingga nilai OWAS menjadi nilai 1 yang berarti tidak ada masalah pada postur akhir. Untuk dimensi antropometri yang digunakan adalah Tinggi bahu berdiri 136,4 cm untuk tinggi keran output, tinggi mata berdiri 148,8 untuk tinggi sakelar mesin, dan jangkauan tangan kedepan untuk jarak keran input. Waktu siklus yang awal dan setelah perancangan adalah 4,8 menit menjadi 3,2 menit.
PERANCANGAN SENSOR SWITCH PRINTER PRODUK SM5300X MENGGUNAKAN METODE QUALITY FUNCTION DEPLOYMENT UNTUK MENGATASI CUSTOMER COMPLAINT DI PT. TEB Afma, Vera Methalina; Irwan, Hery; Ngadiyono, Ngadiyono
SIGMA TEKNIKA Vol 6, No 2 (2023): SIGMATEKNIKA, VOL. 6, N0. 2, November 2023
Publisher : Fakultas Teknik, Universitas Riau Kepulauan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33373/sigmateknika.v6i2.5626

Abstract

One of he problem at PT. TEB is that the assembly process for installing switches on the scale printer without using tools or jigs, and it causes the switch position is not correct because employees only use feeling and hearing when installing and causes undetectable rejects (Can Not Print). Other factor is installing the switch on the printer without using tools can also take quite a long time, resulting in the production of scales being of poor quality. The aim of this research is how to design tools to help install switches on printers using the Quality Function Deployment (QFD) method and it is also hoped that the results of this design make the quality of the scales is even better. Data collection was carried out by distributing questionnaires to 10 people consisting of operators, production leaders and also Quality Control. The results of data collection from the questionnaire showed that it was necessary to add an Assembly Switch Process to the Printer, namely by adding a jig switch. Therefore a new jig design can be used. The output produced after using the switch jig design increased by 68% and the rejected output decreased by 75% so it is considered that the new jig design can increase production results.
HAND SOLDERING PROCESS TRAINING MATERIAL USING ADDIE APPROACH TO SUPPORT E-LEARNING IMPLEMENTATION IN XYZ COMPANY Afma, Vera Methalina; Arifin, Zaenal
SIGMA TEKNIKA VOL 7, NO 1 (2024): SIGMATEKNIKA, VOL. 7, N0. 1, JUNI 2024
Publisher : Fakultas Teknik, Universitas Riau Kepulauan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33373/sigmateknika.v7i1.6178

Abstract

Training is very important to increase the productivity of the company. Without the right training, worker will not understand and not know how to do right process. Worker with right process will be achieve good product. Sometimes, the problem of lack training is no proper training material availability for process. In this paper, author want to create training material for soldering process because soldering process is one of critical process, no proper soldering training material and support e-training as new implementation in XYZ company, and author is using ADDIE approach to create it. From ADDIE approach, author create 2 training phase and 2 types of assessment and training use multi – sensory learning which are visual, auditive, kinesthetic and tactile. In visual, using interactive video, participants watch the video, do the process as they see in the video, give the explanation, and they can ask the trainer if any question. Then worker will get training more about product especially for quality, output and ergonomic. After implementing it, workers is more understand and they can produce good product and right quantity, and trainer is more comfortable to give training for workers.
PENGGUNAAN HEATER SEBAGAI ALTERNATIF EFEKTIF UNTUK PEMANAS PADA MESIN PENGERING IKAN DAN KERUPUK Borrong, Raya Hidayat; Arifin, Zainal; Afma, Vera Methalina
PROFISIENSI : Jurnal Program Studi Teknik Industri Vol 12, No 2 (2024): : PROFISIENSI DESEMBER 2024
Publisher : University of Riau Kepulauan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33373/profis.v12i2.6931

Abstract

ABSTRACT This research aims to determine the effectiveness of using a heater as an alternative heater in fish and cracker drying machines. Conventional heating that uses sunlight or fossil fuels is often inefficient and inconsistent in producing the desired product quality. In this study, electric heaters were tested as the main heat source to overcome this problem. The experimental method was carried out by measuring drying time, energy consumption, and final product quality such as air content, texture, and nutritional value. The research results show that the use of a heater can reduce drying time by up to 30% compared to conventional methods. In addition, energy consumption is more efficient with more consistent product results in terms of texture and air content. The quality of the final product also increases with lower and more stable air content, as well as better texture compared to conventional drying. Therefore, the use of a heater as an alternative heater in fish and cracker drying machines can be considered an effective and efficient solution, providing economic benefits and better product quality.
IMPLEMENTASI METODE FAILURE MODE EFFECT ANALYSIS DAN PDCA DALAM MENINGKATKAN PRODUKTIVITAS FATTY ACID (Studi Kasus : PT. EO-Industri Kimia) Irwan, Hery; Afma, Vera Methalina; Falindo, Agri
SIGMA TEKNIKA Vol 7, No 2 (2024): SIGMATEKNIKA, VOL. 7, N0. 2, NOVEMBER 2024
Publisher : Fakultas Teknik, Universitas Riau Kepulauan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33373/sigmateknika.v7i2.6921

Abstract

PT. EO-Industri Kimia adalah perusahaan Oleokimia yang memproduksi Fatty Acid dari minyak kelapa sawit (CPO). Fatty Acid diperoleh melalui reaksi CPO dengan air pada temperatur 250-260 °C, tekanan 50-55 bar. Ukuran keberhasilan proses Fatty Acid dilihat dari perolehan Splitting Degree yaitu 98% minimal. Dalam proses pengolahan minyak sawit menjadi Fatty Acid di PT. EO, terdapat variasi perolehan nilai Splitting Degree. Pada bulan Februari 2024 rata-rata perolehan Splitting Degree ialah 97,53%. Tujuan penelitian ini adalah agar perolehan Splitting Degree tercapai minimal 98%. Dalam penelitian ini digunakan metode FMEA dan PDCA. FMEA adalah metode yang digunakan untuk mengidentifikasi kegagalan suatu proses. Sedangkan PDCA digunakan untuk perbaikan secara terus. Pada Februari 2024 perolehan rata-rata Splitting Degree ialah 97,53 %. Setelah dilakukan perbaikan menggunakan metode FMEA dan PDCA perolehan Splitting Degree pada Juli 2024 menjadi 98,95%. Penurunan perolehan Splitting Degree disebabkan oleh adanya BE yang terikut ke Splitting Column yang menyebabkan Floater Level Transmitter Stuck, Plug Control valve Fatty Acid dan RGW terkikis. Penyebab kedua ialah akibat adanya kontaminasi air umpan yakni %Gly > 0,2% di air umpan. Untuk meningkatkan perolehan Splitting Degree ialah dengan menjaga level air pada range 1,5 – 3 meter serta memastikan air umpan tidak terkontaminasi Glycerine ( 0,2 % maksimal).
PEMILIHAN SUPPLIER DI INDUSTRI MANUFAKTUR : LITERATUR REVIEW Afma, Vera Methalina
SIGMA TEKNIKA Vol 8, No 1 (2025): SIGMATEKNIKA, VOL. 8, N0. 1, JUNI 2025
Publisher : Fakultas Teknik, Universitas Riau Kepulauan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33373/sigmateknika.v8i1.7652

Abstract

Pemilihan supplier adalah faktor utama yang perlu diperhatikan oleh suatu industri manufaktur. Adapun pengaruh dari pemilihan supplier ini aldah terhadap biaya produksi yang akan dikeluarkan oleh perusahaan. Tujuan dari penelitian ini adalah untuk memahami dan mengetahui bagaimana proses dalam pemilihan supplier di perusahaan manufaktur. Metode yang penulis gunakan adalah literature review dari artikel ilmiah dari jurnal yang bereputasi. Dari literature review ini memaparkan cara dan metode yang digunakan dalam pemilihan supplier di industri manufaktur, metode dan kriteria yang digunakan dalam melakukan pemilihan.
PENURUNAN REJECT SPRAY DUST PADA JORAN PANCING DENGAN METODE PDCA UNTUK MENINGKATKAN KUALITAS PRODUCT DI PT SHIMANO BATAM Sumarya, Edi; Ramadhoni, Rendy; Methalina Afma, Vera
PROFISIENSI : Jurnal Program Studi Teknik Industri Vol 11, No 2 (2023): PROFISIENSI DESEMBER 2023
Publisher : University of Riau Kepulauan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33373/profis.v11i2.5981

Abstract

The quality control process implements continuous improvements using the Plan Do Check Action (PDCA) method. It uses seven tools where quality control is carried out from the initial production process, ongoing production, and up to finished production. Even though the quality control process has been carried out, the quality of the product is still poor, especially in the area of line spray painting. Data per July-September 2023 recorded 873 defective units with the most dominant spray dust defects with 543 defective units. Using the PDCA method aims to map all the problems above, the purpose of this study is to find out the causes of the most dominant reject spray dust and to find out the factors and determine solutions to reduce spray dust rejection. The PDCA method is used to make improvements that are known. several factors cause spray dust rejection due to the lack of routine maintenance procedures resulting in the performance of the spray gun not being maximized, not cleaning the gun spray every time the process changes which causes the rest of the spray to clog, paint that has expired causing the quality of the paint not to be optimal, lack of control over room temperature and the place for sterilization to enter the spray room is a factor for the large number of rejected spray dust. October-December 2023 recorded a decrease in reject spray dust units from 543 units to 243 units reject.
ANALISA TINGKAT CACAT PADA PROSES PENGELASAN DENGAN METODE SIX SIGMA DAN FAILURE MODE AND EFFECTS ANALYSIS (FMEA) Irwan, Hery; Afma, Vera Methalina; Ramadhan, Gilang
SIGMA TEKNIKA Vol 8, No 2 (2025): SIGMATEKNIKA, VOL. 8, N0. 2, NOVEMBER 2025
Publisher : Fakultas Teknik, Universitas Riau Kepulauan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33373/sigmateknika.v8i2.8392

Abstract

Welding is an important process in the shipbuilding industry that affects the strength and safety of ship structures. At PT BVS, the Flux Cored Arc Welding (FCAW) process still produces a high defect rate, particularly types of defects such as porosity, slag inclusion, undercut, root concavity, and lack of fusion. Based on data from January to May 2025, the reject rate reached 56%, far exceeding the company's standard of 10%. This study aims to identify the types and causes of defects in FCAW welding, as well as provide improvement proposals using the Failure Mode and Effects Analysis (FMEA) method. The analysis show that the three causes with the highest RPN values come from human factors, methods, and machines. Improvement proposals include operator training, preparation of welding Standard Operating Procedures (SOP), regular equipment condition checks, and adjustment of welding parameters. The implementation of these improvement proposals is expected to reduce the defect rate, improve the quality of welding results, and minimize rework costs and production delays. This study provides practical contributions for companies in enhancing welding quality and serves as a reference for quality control in the shipbuilding industry.
PEMILIHAN SUPPLIER BERKELANJUTAN PADA INDUSTRI MANUFAKTUR DENGAN MEMPERTIMBANGKAN METODE DAN KRITERIA PEMILIHAN: TINJAUAN PUSTAKA Afma, Vera Methalina; Hadiguna , Rika Ampuh; Adi , Alexie Herryandie Bronto
JURNAL REKAYASA SISTEM INDUSTRI Vol 11 No 1 (2025): November 2025
Publisher : Universitas Putera Batam

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33884/jrsi.v11i1.10781

Abstract

Supplier selection plays a pivotal role in the operational efficiency and cost management of manufacturing industries. Appropriate supplier choice directly affects the production costs and overall competitiveness of a company. This study aims to explore the supplier selection process within manufacturing firms through the application of Multi-Criteria Decision Making (MCDM) methods. A systematic literature review was conducted using scientific articles indexed in Scopus, analyzed with the Bibliometrix package in R Language. The findings highlight various MCDM approaches utilized in supplier evaluation and selection, along with the key criteria considered in decision-making processes. This research contributes to a deeper understanding of methodological trends and practical considerations in supplier selection, offering insights for both academic and industrial applications. Keywords: supplier selection, manufacturing, MCDM, literatur review