Claim Missing Document
Check
Articles

Found 11 Documents
Search
Journal : Bulletin of Chemical Reaction Engineering

CuAl LDH/Rice Husk Biochar Composite for Enhanced Adsorptive Removal of Cationic Dye from Aqueous Solution Neza Rahayu Palapa; Tarmizi Taher; Bakri Rio Rahayu; Risfidian Mohadi; Addy Rachmat; Aldes Lesbani
Bulletin of Chemical Reaction Engineering & Catalysis 2020: BCREC Volume 15 Issue 2 Year 2020 (August 2020)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.15.2.7828.525-537

Abstract

The preparation of CuAl LDH and biochar (BC) composite derived from rice husk and its application as a low-cost adsorbent for enhanced adsorptive removal of malachite green has been studied. The composite was prepared by a one-step coprecipitation method and characterized by X-ray Diffraction (XRD), Fourier Transform Infra Red (FTIR), Brunauer-Emmett-Teller (BET), and Scanning Electron Microscopy - Energy Dispersive X-ray (SEM−EDX). The result indicated that CuAl LDH was successfully incorporated with the biochar that evidenced by the broadening of XRD peak at 2θ = 24° and the appearance of a new peak at 1095 cm−1 on the FTIR spectra. The BET surface area analysis revealed that CuAl/BC composite exhibited a larger surface area (200.9 m2/g) that the original CuAl LDH (46.2 m2/g). Surface morphological changes also confirmed by SEM image, which showed more aggregated particles. The result of the adsorption study indicated the composite material was efficient in removing malachite green with Langmuir maximum adsorption capacity of CuAl/BC reaching 470.96 mg/g, which is higher than the original CuAl LDH 59.523 mg/g. The thermodynamic analysis suggested that the adsorption of malachite green occurs spontaneously (ΔG < 0 at all tested temperature) and endothermic nature. Moreover, the CuAl/BC composite showed strong potential as a low-cost adsorbent for cationic dye removal since it showed not only a high adsorption capacity but also good reusability. Copyright © 2020 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 
Preparation of Ca/Al-Layered Double Hydroxides/Biochar Composite with High Adsorption Capacity and Selectivity toward Cationic Dyes in Aqueous Risfidian Mohadi; Neza Rahayu Palapa; Aldes Lesbani
Bulletin of Chemical Reaction Engineering & Catalysis 2021: BCREC Volume 16 Issue 2 Year 2021 (June 2021)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.16.2.10211.244-252

Abstract

Widely reports have evaluated the use of biochar (BC) composites to layered double hydroxide (LDH) to adsorb dyes from wastewater. However, its applicability for adsorbing a mixture of cationic dyes such as Malachite green (MG), Rodhamine-B (Rh-B), and Methylene blue (MB), which causes carcinogenic and mutagenic effects on aquatic life, has not been studied. In this work, we compared the performance of CaAl-LDH/BC adsorbent with or without the addition of BC in the adsorption of cationic dyes. The adsorption study was prepared in a batch system using various temperatures, concentrations, and also contact time. The results of the characterization of Ca/Al-Biochar composite showed the unique diffraction of XRD pattern, and also showed two characteristics of starting materials. Surface area analysis by BET method showed Ca/Al-Biochar composite has a higher surface area than starting material. The results of the adsorption study of MG showed that Ca/Al-Biochar follows the pseudo-second-order kinetic model. The adsorption capacity of MG on Ca/Al-Biochar was up to 71.429 mg/g and shows selectivity toward MG in an aqueous solution. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 
Removal of Iron(II) Using Intercalated Ca/Al Layered Double Hydroxides with [α-SiW12O40]4- Tarmizi Taher; Mikha Meilinda Christina; Muhammad Said; Nurlisa Hidayati; Ferlinahayati Ferlinahayati; Aldes Lesbani
Bulletin of Chemical Reaction Engineering & Catalysis 2019: BCREC Volume 14 Issue 2 Year 2019 (August 2019)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.14.2.2880.260-267

Abstract

Ca/Al layered double hydroxide (LDH) was successfully synthesized by co-precipitation method at pH 11 under room temperature condition then followed by calcination at 800 oC. The synthesized Ca/Al LDH was further intercalated with Keggin ion [α-SiW12O40]4- in order to prepare the intercalated form of Ca/Al LDH. The synthesized materials were characterized by X-ray diffraction (XRD) and Fourier transform infrared (FT-IR) and used as an adsorbent for iron(II) removal from the aqueous medium. The adsorption performance was investigated by studying the kinetics and thermodynamic properties of the adsorption process. The results showed that pristine Ca/Al LDH exhibited diffraction peak at 2θ about 20o which corresponds to the layer structure of the LDH material. For the intercalated Ca/Al LDH, the diffraction observed at 2θ around 30-40o indicated that the [α-SiW12O40]4- was successfully intercalated into the interlayer space of Ca/Al LDH. Furthermore, the intercalated Ca/Al LDH showed higher adsorption capacity toward iron(II) than the pristine form of Ca/Al LDH. 
Size Selectivity of Anionic and Cationic Dyes Using LDH Modified Adsorbent with Low-Cost Rambutan Peel to Hydrochar Normah Normah; Novie Juleanti; Patimah Mega Syah Bahar Nur Siregar; Alfan Wijaya; Neza Rahayu Palapa; Tarmizi Taher; Aldes Lesbani
Bulletin of Chemical Reaction Engineering & Catalysis 2021: BCREC Volume 16 Issue 4 Year 2021 (December 2021)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.16.4.12093.869-880

Abstract

Modification of the layered double hydroxide of CuAl-LDHs by composite with hydrochar (HC) to form CuAl-HC LDH. Material characterization by XRD, FT-IR and SEM analysis was used to prove the success of the modification. The characterization of XRD and FT-IR spectra showed similarities to pure LDH and HC. Selectivity experiments were carried out by mixing malachite green, methylene blue, rhodamine-B, methyl orange, and methyl red to produce the most suitable methyl blue dye for CuAl-LDH, HC and CuAl-HC adsorbents. The effectiveness of CuAl-HC LDH as adsorbent on methylene blue adsorption was tested through several influences such as adsorption isotherm, thermodynamics, and adsorbent regeneration. CuAl-HC LDH adsorption isotherm data shows that the adsorption process tends to follow the Langmuir isotherm model with a maximum adsorption capacity of 175.439 mg/g with a threefold increase compared to pure LDH. The effectiveness of the adsorbent for repeated use reaches five cycles as evidenced by the maximum capacity regeneration data reaching 82.2%, 79.3%, 77.9%, 76.1%, and 75.8%. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 
Efficient Adsorption of Methylene Blue Dye Using Ni/Al Layered Double Hydroxide-Graphene Oxide Composite Amri, Amri; Wibiyan, Sahrul; Wijaya, Alfan; Ahmad, Nur; Mohadi, Risfidian; Lesbani, Aldes
Bulletin of Chemical Reaction Engineering & Catalysis 2024: BCREC Volume 19 Issue 2 Year 2024 (August 2024)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.20121

Abstract

To address environmental pollution, we developed Ni/Al layered double hydroxide-graphene oxide (Ni/Al-GO) adsorbent materials for the purpose of eliminating methylene blue (MB) dye pollutants. The adsorption process was explored by examining many experimental factors, including temperature, regeneration/reuse procedure, pH, and time, and their effects on the material. The appropriate model for the isotherm is the Langmuir isotherm. The Ni/Al-GO material achieved a maximum adsorption capacity of 61.35 mg/g for MB dye at a temperature of 60 °C. The thermodynamic characteristics indicate that the adsorption process is both endothermic and spontaneous as the temperature increases. The regeneration method demonstrated that the Ni/Al-GO material has a highly stable structure, enabling it to be utilized for five cycles with a remarkable regeneration rate of 93.49% in the fifth cycle. The pH that yielded the best results for all materials was pH 10, and the kinetic model demonstrated a pseudo second-order behavior. Copyright © 2024 by Authors, Published by MKICS and BCREC Publishing Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0).
Comparison of LDH-Organic/Inorganic Compound Modified Materials as Adsorbents for Heavy Metal Adsorption: Characteristic Structure and Adsorption Mechanism Normah, Normah; Lesbani, Aldes
Bulletin of Chemical Reaction Engineering & Catalysis 2024: BCREC Volume 19 Issue 2 Year 2024 (August 2024)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.20160

Abstract

This study modified layered double hydroxide (LDH) with organic compounds in hydrochar made from rambutan peels (prepared by hydrothermal method) and polyoxometalate compounds (tipe Keggin K4[ -SiW12O40].nH2O compound and prepared by sol-gel method). The synthesis of modified material was conducted through the coprecipitation method. The material was then applied as an adsorbent for Fe²⁺ ions. The material's properties were analyzed using XRD (X-ray diffraction), FT-IR (Fourier-transform infrared spectroscopy), and BET surface area analysis. The physicochemical characteristics of the modified material, a combination of the pure LDH and hydrochar/polyoxometalate compounds, will influence the adsorption results of Fe²⁺ metal ions. Furthermore, its application as an adsorbent was analyzed through kinetic and isotherm parameters, which were found to follow the pseudo-first-order (PFO) and Freundlich models. The adsorption capacities for NiAl-LDH, NiAl-LDH/Hc (modified with Hc), and NiAl-LDH/POM (modified with POM) materials were 32.789 mg/g, 47.393 mg/g, and 90.091 mg/g, respectively. It can be concluded that the adsorption process occurs via physisorption, forming multilayer adsorbates at the adsorbents active sites. Copyright © 2024 by Authors, Published by BCREC Publishing Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0)
CuAl-LDH Modified with Filamentous Macroalgae for Anionic Dyes Removal: A Study on Selectivity, Adsorption Efficiency, and Regeneration Wijaya, Alfan; Hanum, Laila; Melwita, Elda; Lesbani, Aldes
Bulletin of Chemical Reaction Engineering & Catalysis 2024: BCREC Volume 19 Issue 4 Year 2024 (December 2024)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.20223

Abstract

Continuous modifications of Layered Double Hydroxides (LDH) materials are essential to enhance their structural stability and improve their capacity for pollutant adsorption, addressing the need for more effective remediation strategies in environmental applications. This research study has proposed the preparation of CuAl-LDH supported filamentous macroalgae of Spirogyra sp. (CuAl-LDH/SA) via coprecipitation and hydrothermal methods. The prepared CuAl-LDH/SA composites were investigated for the adsorption of direct yellow 12 (DY) and remazol red (RR) dyes in batch mode experiments. The structure and morphology of the prepared CuAl-LDH/SA were identified by X-ray Diffraction (XRD), Fourier Transform Infra Red (FT-IR), (Brunauer-Emmett-Teller) BET surface area, Thermogravimetry / Differential Thermal Analyzer (TG/DTA), and Scanning Electron Microscope (SEM). For the adsorption process, the effects of initial pH, contact time, initial concentration, temperature, adsorption selectivity, and adsorbent regeneration, as well as kinetics, isotherms, and thermodynamics were studied. The adsorption selectivity test resulted in the RR dye being more selective compared to DY. The maximum capacities for RR adsorption were 72.464 mg/g (pH = 2, 150 min, 303 K). CuAl-LDH/SA can be regenerated for 4 cycles with a percent removal of 29.32%. The adsorption process followed the intraparticle diffusion kinetics model and Langmuir isotherm. Thermodynamic studies showed that the adsorption of RR using CuAl-LDH/SA was endothermic and spontaneous. The results of this study indicate that CuAl-LDH/SA composite material shows potential material in the removal of anionic dyes from aqueous solutions. Copyright © 2024 by Authors, Published by BCREC Publishing Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0).
Enhanced Removal Efficiency of Malachite Green Dye Using Gambir Leaf Extract-Modified NiFe LDH Composites: A Study of Cationic Dye Adsorption Jefri, Jefri; Fithri, Najma Annuria; Lesbani, Aldes
Bulletin of Chemical Reaction Engineering & Catalysis 2024: BCREC Volume 19 Issue 4 Year 2024 (December 2024)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.20215

Abstract

A NiFe layered double hydroxide (LDH) composite with Uncaria gambir (UG) leaf extract was successfully synthesized. The composite (NiFe-UG LDH) and the base material (NiFe LDH) were identified using X-ray Diffraction (XRD), Fourier Transform Infra Red (FTIR), and Brunauer-Emmett-Teller (BET) Surface Area techniques. The XRD and FTIR results revealed the incorporation of gambier leaf extract into the NiFe LDH structure, as indicated by the combined diffraction patterns and spectral features. The BET analysis indicated a decrease in the surface area of NiFe-UG LDH compared to that of NiFe LDH, suggesting that active compounds from the gambier leaf extract effectively coated the LDH surface and blocked its pores. During malachite green (MG) adsorption, NiFe-UG demonstrated faster adsorption kinetics and a higher adsorption efficiency, reaching 96.420% compared to 92.085% for NiFe LDH. While both materials followed pseudo-first-order kinetics, their isotherm behaviors differed: NiFe-UG adhered to the Langmuir model, indicating monolayer adsorption, whereas NiFe LDH followed the Freundlich model, signifying multilayer adsorption. Further analysis suggested that adsorption in NiFe LDH was primarily governed by physisorption, while in NiFe-UG, a combined physisorption-chemisorption mechanism occurred. These results underscore the enhanced adsorption capacity of the composite material, attributed to the introduction of additional functional groups from the gambier leaf extract. Copyright © 2024 by Authors, Published by BCREC Publishing Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0).
Treatment of Methylene Blue Using Ni-Al/Magnetite Biochar Layered Double Hydroxides Composite by Adsorption Zahara, Zaqiya Artha; Royani, Idha; Palapa, Neza Rahayu; Mohadi, Risfidian; Lesbani, Aldes
Bulletin of Chemical Reaction Engineering & Catalysis 2023: BCREC Volume 18 Issue 4 Year 2023 (December 2023)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.20049

Abstract

Methylene blue dye is hard to degrade and requires treatment using Ni-Al Layered double hydroxides (LDHs) modified with magnetite biochar (MBC) to form Ni-Al/magnetite biochar composite in overcoming environmental pollution. Material attainment was identified by characterization using X-Ray Diffraction (XRD), Fourier Transform – Infra Red (FT-IR), Branuer Emmet Teller (BET), Scanning Electron Microscopy – Energy Dispersive X-Ray (SEM-EDX) and Vibration Sample Magnetometer (VSM). XRD characterization displays angle 2θ at 11°, 60° is a typical angle of LDH, and angles 22° and 35° of magnetite biochar. FT-IR characterization analysis at wavelength 1381 cm-1 for NO3- group and M-O group at wave number 700 cm-1. C-H group on biochar at 1404 cm-1 and wave number 586 cm-1 for Fe-O group. BET characterization analysis of Ni-Al/MBC has a large surface area and pore volume of 127.310 m²/g and 0.1950 cm³/g. SEM characterization analysis of Ni-Al/MBC has large, coarse pores and non-uniform shape, EDX data shows that there are forming elements such as Ni, Al from LDH and, Fe, C elements from magnetite biochar. pH, kinetics, isotherms, and thermodynamics become influential in adsorption processes. The adsorption capacity of the composite reaches 68.493 mg/g by following the Langmuir equation and adsorption kinetics refers to the Pseudo Second Order (PSO) equation. Adsorption continuity is spontaneous and endothermic. Ni-Al/MBC has stability in the process of adsorbent regeneration up to five adsorption cycles and, therefore can be used as a potential adsorbent in the treatment of methylene blue dye in aqueous environmental pollution. Copyright © 2023 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 
Recycle Performance of Heterogeneous Catalyst Metal Oxides-Based Layered Double Hydroxide for Oxidative Desulfurization Process of 4-methyldibenzothiophene Ahmad, Nur; Rohmatullaili, Rohmatullaili; Hanifah, Yulizah; Wibiyan, Sahrul; Amri, Amri; Wijaya, Alfan; Mardiyanto, Mardiyanto; Mohadi, Risfidian; Royani, Idha; Lesbani, Aldes
Bulletin of Chemical Reaction Engineering & Catalysis 2023: BCREC Volume 18 Issue 4 Year 2023 (December 2023)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.20034

Abstract

The desulfurization of oil must be resolved as soon as possible due to a variety of issues, including environmental contamination and protection regulations. It was believed that oxidative desulfurization (ODS) was the most promising method. In this research, metal oxide-based layered double hydroxides (TiO2@Ni-Al and ZnO@Ni-Al) were effectively synthesized for the ODS of 4-methyldibenzothiophene (4-MDBT). TiO2@Ni-Al and ZnO@Ni-Al exhibited superior catalytic performance and high recycling capacity, achieving a 99% removal rate after five reactions in 30 min. The heterogeneous catalyst TiO2@Ni-Al/ZnO@Ni-Al is easy to separate and recover from a reaction system. Increased temperature facilitates the transformation of 4-MDBT into 4-MDBTO2. The influence of H2O2's rapid decomposition rate, which can inhibit oxidation reactions, reduces the catalytic activity as the temperature increases. 4-MDBT Sulphur removal on TiO2@Ni-Al and ZnO@Ni-Al is 99.48 and 99.51%, respectively. TiO2@Ni-Al and ZnO@Ni-Al have great potential for use in the industry based on these results. Copyright © 2023 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 
Co-Authors A. Agnes Abi Sueb Abriyanto, Danang Addy Rachmat Adi Saputra Adi Saputra Adi Saputra Adi Saputra Afifah Rahma Dian Ahmad Fatoni Ahmad Fatoni Alfan Wijaya Alfan Wijaya Alfan Wijaya Amiruddin Supu Amri Amri Amri Andi Wijaya Andreas, Roy Andriani Azora Andriani Azora Anggraini, Ana Arini Fousty Badri Arini Fousty Badri Arison Musri Arison Musri Arsyad, Fitri Suryani Aslihati Aslihati Aslihayati Aslihayati Azhar Kholiq Badri, Arini Fousty Bakri Rio Rahayu Bakri Rio Rahayu Benyamin Lakitan Dedi Rohendi Dedi Setiabudidaya Desnelli Desnelli Dian Monariqsa Dian Monariqsa Didi Jasantri Dormian A N Haloho Dormian A N Haloho Eiffel Ostan Jeski Gultom Elfita Elfita . Elfita Elfita Eliza . Eliza Eliza Eliza Eliza Ema Veronika Turnip Endri Junaidi Eriza Sativa Erviana, Desti Fahma Riyanti Fatmawati Fatmawati Ferlinahayati Ferlinahayati Fitri Suryani Arsyad Fitri, Erni Salasia Fitriliana Fitriliana Hanifah, Yulizah Haris Kriswantoro Hermansyah Hermansyah Hermansyah Hermansyah Hesti A. Harahap Hesti A. Harahap, Hesti Hidayatullah, Muhammad Hilda Zulkifli Hilda Zulkifli Hilda Zulkifli Hiroshi Nishihara Hitoshi Kondo Idha Royani Intan Permata Sari Irfannuddin Irfannuddin Jasantri, Didi Jefri Jefri Jeri Ramadhan Juleanti, Novie Kiki Anggraini Kiki Anggraini Kiki Anggraini, Kiki Komis Krisna Murti Laila Hanum Leni Sinaga Lestari Simanjuntak Lestari Simanjuntak Liasari, Beta Riana Lingga, Fitra Wahyuni Lora Vitanesa Lucyanti . Lucyanti Lucyanti Lusi Teresia Mardianto Mardiyanto Mardiyanto Mardiyanto Mardiyanto Mardiyanto Mardiyanto Mardiyanto Mardiyanto Mardiyanto Mardiyanto Mardiyanto Mardiyanto, Marieska Verawaty Mariska Verawaty Melantina Melan Oktriyanti Melwita, Elda Menik Setyowati Mikha Meilinda Christina Miksusanti Miksusanti Muhammad Imron Muhammad Said Muhammad Said Muhammad Said MUHAMMAD SAID Najma Annuria Fithri Najma Annuria Fithri Najma Annuria Fithri Najma Annuria Fithri, Najma Annuria Narsito Narsito Neza Rahayu Niken Oktora Niken Oktora Nirwan Syarif Normah Normah Normah Normah, Normah Nova Yuliasari Novie Juleanti Novie Juleanti Novie Juleanti Nur Ahmad Nur Ahmad, Nur Nurlisa Hidayati Nurlisa Hidayati Nurlisa Hidayati Nurlisa Hidayati Nurlisa Hidayati Nurlisa Hidayati Nurlisa Hidayati Nurlisa Hidayati Nurlisa Hidayati Nurlisa Hidayati Nurlisa Hidayati Nur’aini, Siti Nyanyu Ummu Hani Palita Tamba Patimah Mega Syah Bahar Nur Siregar Patimah Mega Syah Bahar Nur Siregar Patimah Mega Syah Bahar Nur Siregar Poedji Loekitowati Hariani Putri Erlyn Putri, Bunga Indah R.A. Mika Melviana Rabelia Juladika Sayeri Radja Nardo Purba Rakhmawati Farma Ramadhan, Jeri Rananda Vinsiah Randi O. Saragih Ratna, L.P Ratna, L.P Risfidian Mohadi Risfidian Mohadi Risfidian Mohadi Risfidian Mohadi Risfidian Mohadi Risfidian Mohadi Risfidian Mohadi Risfidian Mohadi Risfidian Mohadi Risfidian Mohadi Risfidian Mohadi Risfidian Mohadi Risfidian Mohadi Risfidian Mohadi Risfidian Mohadi Risfidian Mohadi Risfidian Mohadi Risfidian Mohadi Risfidian Mohadi Risfidian Mohadi Risfidian Mohadi Risfidian Mohadi Risfidian Mohadi Risfidian Mohadi Risfidian Mohadi Risma Kurniawati M Rohmatullaili Rohmatullaili, Rohmatullaili Roy Andreas Sabat Okta Ceria Sitompul, Sabat Okta Ceria Samat Samat Savira, Dila Setiawan Yusuf Setiawati Yusuf Setiawati Yusuf Sherly Agustina, Sherly Siregar, Patimah Mega Syah Bahar Nur Sitanggang, Jonra P. Soerya, Balada Sri Juari Santosa Suheryanto Suheyanto Suheryanto Sumiati Sumiati SUMIATI, Susila Arita Syaflina Lamin Syafrina Lamin, Syafrina Tamizi Taher Tarmizi Taher Welinda Me Wibiyan, Sahrul Wijaya, Alfan Winda Fitriana Yeni Iswanti Yoshinori Yamanoi Yosi Saria Yosi Saria Yosi Saria Yosine Susi Yosine Susie Yunita Irianty Zahara, Zaqiya Artha Zazili Hanafiah Zultriana