Claim Missing Document
Check
Articles

PELAPISAN PERMUKAAN BAJA TAHAN KARAT AISI 304 DENGAN KHROM OKSIDA MENGGUNAKAN METODA SPUTTERING Sungkono; Jan Setiawan; Isfandi; Ikhwanul Aziz
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 25 No. 2 (2019): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2019.25.2.5433

Abstract

Stainless steel has been used as structure material of power reactors of LWR, AGR and LMFBR types. The problem of structural materials that arises is low corrosion resistance and swelling in high irradiation environments. One method to overcome this problem is surface coating of the stainless steel cladding with chromium oxide. The aim of this study is to obtain the characteristics of microstructure, microhardness, and compounds formed in the surface layer of AISI 304 stainless steel. DC-sputtering method was used for the coating of AISI 304 surface. The coating process used coater material of chromium target and argon as sputtering gas which was mixed with oxygen gas with concentrations varying from 0 - 50% volume. The process was carried out at 10 - 20 mA current for 1 - 3 hours. Characterization of the layer includes microstructure observation using optical microscope, hardness with microhardness Vickers tester, and compounds analysis in layers with X-ray diffractometer. The results shows that the base metal microstructure is composed of austenite and carbide deposits. The metal-layer interface is clearly visible. The thickness of the resulted compact and homogeneous layer tends to increase for O2 gas composition in the range of 0 – 30 %volume but decrease for the range of 30 - 40 %volume and rise at 40 - 50 %volume. The hardness of the layer increases until oxygen gas is at 30 %volume and then decreases at 50 %volume of O2 gas. At a fixed value of O2 composition at a current of 10 - 20 mA and a process time of 1 - 3 hours, it is observed that the hardness of the SS 304 surface layer increases with increasing current and sputtering time. At a composition of 30 %volume of O2, 10 mA current and 2 hours process, the resulted layer contains CrO2.
PERILAKU ELEKTROKIMIA BAJA TAHAN KARAT SS 316 DALAM MEDIA NANO FLUIDA Djoko Hadi Prajitno; Jan Setiawan
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 25 No. 1 (2019): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2019.25.1.5053

Abstract

Corrosion is a common problem in many engineering metals and alloys. Electrochemical method is powerful instrument to use as tool to study corrosion behavior of metals and alloys in corrosive environment. The present study is to evaluate interaction between stainless steel SS 316 and nanofluid containing nano particles of ZrO2 as an additive to demineralized water by electrochemical method. Corrosion potential, Tafel polarization, and electrochemical impedance spectroscopy (EIS) of stainless steel SS 316 were performed in both demineralized water and demineralized water containing nano particle 0.05% ZrO2 at different immersion time. Corrosion potential examination shows that stainless steel 316 is actively corroded in both demin water and nanofluid. The corrosion potential tends to increase toward positive value for longer immersion time, both in demin water and nanofluid media. The value of anodic Tafel slope of also tends to increase for longer immersion time, both in demin water and nanofluid. Tafel polarization examination shows that corrosion rate of stainless steel 316 in demin water and nanofluid is not significantly different, and corrosion rate decreases with immersion time. EIS technique shows that the impedance of stainless steel 316 in nanofluid is higher when compared to the impedance in demineralized media, resulting in lower corrosion rates in nano fluids. X-ray diffraction examination of the specimens shows that the phase present in the stainless steel 316 alloys after corrosion testing is γ austenite, both in demin water and nanofluid. Stainless steel SS 316 is very good corrosion resistant material both in demin water and nanofluid with corrosion rate under 1 MPY.
KARAKTERISTIK MEKANIK KELONGSONG BAHAN BAKAR NUKLIR TEMPERATUR TINGGI DALAM ATMOSFER GAS NITROGEN Rohmad Sigit; Sri Ismarwanti; Guswardani; Yatno Dwi Agus Susanto; Jan Setiawan
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 24 No. 2 (2018): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2018.24.2.4422

Abstract

At Loss of Cooling Accident (LOCA) scenario, Zr-2 and Zr-4 as nuclear fuel cladding potentially exposed to air which experimentally leads to mechanical properties degradation faster than in steam environment. This study aims to determine the impact of nitrogen on the mechanical strength of cladding by minimizing other environmental influences. The Zr-2 and Zr-4 cladding was annealed under vacuum at a temperature of 500°C for one hour. It was followed by nitriding with the pressure of 1500 mbar for two hours. It was followed by natural cooling to room temperature. The results of tensile strength and microhardness testing showed that tensile strength, ductility and microhardness values increase of 12.1%, 19.2% and 28.2% for Zr-2 and 5.1%, 25% and 22.6% for Zr-4, respectively. Nitride layer was formed on the cladding surface due to interaction with nitrogen and there is no mechanical properties degradation due to nitriding process. It was caused by nitriding processes that were not followed or accompanied by oxidation processes.
ANALISIS KETIDAKPASTIAN PENGUKURAN KEKUATAN TARIK DAN ELONGASI SPESIMEN SS304 BERBENTUK RING Sri Ismarwanti; Jan Setiawan; Maman Kartaman Ajiriyanto; Rohmad Sigit
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 27 No. 3 (2021): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2021.27.3.6567

Abstract

Uncertainty is a measure of the reliability of a measurement. One of the widely used uncertainty analysis approaches is the Guide to the expression of uncertainty in measurement (GUM). The steps for analyzing the uncertainty of a measurement have been described in detail by the GUM approach. Uncertainty analysis was carried out on tensile testing to determine the traceability of the data obtained. Tensile testing produces data in the form of tensile strength and elongation of the test material. Tensile strength is a quantity that involves the magnitude of the force and length. Elongation is the increase in length when pulling. The tensile strength of the ring-shaped sample will be affected by the cross-sectional area on both sides of the ring when a tensile stress is applied. So, to determine the uncertainty of the tensile test, an analysis of the contributors to the uncertainty is required. This paper provides an explanation of how to analyze the uncertainty of the measurement of tensile strength and elongation in a ring-shaped sample. In addition, the value of the uncertainty in the measurement of tensile strength and elongation of SS304 (in the form of a ring) will also be presented. The test results show that the average tensile strength of SS304 rings is 631.070 ± 26.976 Nmm-2 with an expanded uncertainty of 50.451 Nmm-2 at a 95% confidence level. In addition, at the same level of confidence, the average SS304 ring elongation result is 18.681% ± 2.425% with an expanded uncertainty of 2.867%. Data repetition or repeatability is the biggest contributor to the uncertainty in measuring the tensile strength and elongation of the SS304 ring.
IDENTIFIKASI FASA PADA PELET BAHAN BAKAR U-ZrHx HASIL PROSES SINTER DENGAN ATMOSFER NITROGEN Masrukan; Jan Setiawan; Dwi Biyantoro
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 23 No. 3 (2017): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2017.23.3.3641

Abstract

Phases identification of U-ZrHX fuel pellets sintered under nitrogen atmosphere has been carried out. This sintering process is intended to obtain higher density pellets that meet the requirements for use as a fuel in pressurized water reactor (PWR). The results of this study are expected to be used for the determination of phase and density changes occurred in U-ZrHx pellets at various Zr concentrations after sintering at various temperatures. PWR fuel from U-ZrHx pellet needs to be sintered to increase its density. At first, pellets made from U-ZrHx powder with Zr composition of 35, 45 and 55 wt.% through a pressing process at a pressure of 509-637 MPa. The resulted U-ZrHx green pellets were subsequently sintered under nitrogen gas atmosphere at 1200 °C and 1300 °C for a fixed sintering time of one hour. Phase analysis of the sintered U-ZrHx pellets was done by X-ray diffraction (XRD) technique and the data obtained were processed by using HighScore Plus software. The test results with XRD indicate the formation of phases such as U(ZrHr2), UO3, UO2, and Zr. The UO2 and Zr phases were characterized for their density, lattice parameter and percentage of weight. In this experiment it is desired to obtain U-ZrHx with high density without the formation of many phases. Density measurement shows that the density of zirconium metal and UO2 decreases with increasing sintering temperature (from 1200 °C to 1300 °C), while the lattice parameter increases with increasing sintering temperature. Data calculation of weight percentage for sintering at 1300 °C shows that the percentage values of the resulted zirconium metal and uranium dioxide are the closest to their theoretical calculation results.
KARAKTERISTIK DAKTILITAS SS304 YANG TEROKSIDASI PADA TEMPERATUR TINGGI Jan Setiawan; Sungkono
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 23 No. 3 (2017): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2017.23.3.3645

Abstract

This paper shows changes in hardness, tensile strength and ductility characteristics of SS304. The SS304 was processed by heat treatment at high temperature in atmospheric environment. SS304 is a type of stainless steel with many superior properties used in industry. In this research, a pipe made of SS304 with 30 mm in diameter was cut in transversal direction at 3 mm width to be used as a sample. The samples were processed by heat treatment at 600, 800 and 1000 °C for 1 and 2 hours in atmospheric environment. After the oxidation process, the samples were cooled by natural cooling outside the furnace or quenched in water. Hardness testing and ring tensile testing were done to the high-temperature oxidized SS304. Analyses were done to study changes in hardness, tensile strength and ductility characteristics of SS304 after oxidation process. The results show that hardness escalation occurs mainly for samples that were cooled by quenching in water compared to natural cooling. The highest hardness value was observed for the sample oxidized at 1000 °C for 1 hour and cooled by quenching, where hardness value changed from 281.25 HV before oxidation to 468.00 HV after oxidation. The tensile strength of the samples, however, tend to decrease, while the ductility of some samples tends to increase. Increase in tensile strength followed by increase in ductility occurs for samples oxidized at 600 °C for 2 hours with natural cooling. The tensile strength after oxidation reaches a value of 744.04 MPa with 12.38 % elongation escalation. As a guidance for implementation, SS304 in high temperature oxidation environment should be limited by temperature of 600 °C.
PENGARUH HIDROGEN TERHADAP KEKUATAN TARIK KELONGSONG BAHAN BAKAR NUKLIR BERBASIS PADUAN ZIRKONIUM Rohmad Sigit; Fajar Al Afghani; Jan Setiawan; Sungkono
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 23 No. 3 (2017): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2017.23.3.3648

Abstract

During reactor operation, zircaloy-4 (Zr-4) as fuel cladding is under an environment that can potentially cause mechanical failure, especially by the effect of cladding-hydrogen interaction. Hydrogen would diffuse and precipitate to form brittle hydrides when the solubility limit is surpassed. In this experiment, ring tensile test method was used to examine the effect of hydrides existence on tensile strength of Zr-4 cladding. The Zr-4 sample was annealed at 500 °C and 600 °C for an hour in vacuum condition and followed by hydriding with a pressure up to 1000 mbar with 3 hours holding time and slow cooling. According to ideal gas equation, hydrogen content in Zr-4 reaches about 674 ppm and 1215 ppm at hydriding temperature of 500 °C and 600 °C respectively. Microstructure observation shows that hydrides precipitate was formed at grain boundaries. The hydrides were found to be longer and thicker at higher hydriding temperature. As the hydrogen content increases, the ring tensile test shows increasing stress at 4.4 %, decreasing strain at 2.1 % and increasing microhardness level at 13 %. This result confirms that the existence of hydrides precipitates in cladding has an effect of increasing the tensile strength and decreasing the ductility obviously.
KARAKTERISTIK INGOT PADUAN U-Zr-Nb PASCA PROSES QUENCHING Masrukan; Jan Setiawan
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 23 No. 2 (2017): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2017.23.2.3522

Abstract

The U-Zr-Nb heat-quenching experiment has been subjected to various Nb compositions. Ingots of U-Zr-Nb alloys with varying Nb compositions are 1%, 4% and 7% and a fixed 10% Zr composition is made by melting U, Zr and Nb metals in an electric arc furnace. The quenching experiment is intended to convert an unstable phase αU into stable γU phase. Quenching experiment is intended to convert an unstable phase αU phase into a stable γU phase. In quenching experiments, the U-10Zr-1Nb, U-10Zr-4Nb, U-10Zr-7Nb ingot ingredients were fed into box that made of steel plate and then fed into a heating furnace and heated at 900 C and held for 2 hours for then cooled rapidly in water. After quenched then subjected to phase testing and microstructure observation. The phase test is performed using X-ray diffraction (XRD) and the data is processed using HighScore software, while the microstructure observation using optical microscope. Test results with XRD showed that the U-10Zr-1Nb alloy before quenched consisted only of an αU phase, the U-10Zr-4Nb alloy consist of 23,1504% αU phases and 76,8495% γU phases, while U-10Zr-7Nb consist of 34,1873% αU phases and 65,8127% γU phases. For U-10Zr-1Nb alloys after quenched consist of an αU phase, the U-10Zr-4Nb alloy consist of 44% αU phases and 46% γU phases, the U-10Zr-7Nb alloy consisted of 19% αU and 81% phases γU. For U-10Zr-1Nb alloys after quenched consist of an αU phase, the U-10Zr-4Nb alloy consisted of 44,6711% αU phases and 55,3289% γU phase, the U-10Zr-7Nb alloy consist of 17,9918% αU phases and of 82,0082% γU phases. The results of the theoretical density analysis on the phases formed on U-10Zr-1Nb, U-10Zr-4Nb, U-10Zr-7Nb alloys both before and after quenched were obtained that ingot of U-10Zr-1Nb, U-10Zr-4Nb alloy U-10Zr-7Nb shows that the αU and γU phase densities decrease slightly if the Nb content is lower. Meanwhile, microstructure observation results showed that in the higher of Zr content (7% Nb) will form smaller grains (fine) after quenching. It can be concluded that the quenching process of U-10Zr-1Nb, U-10Zr-4Nb and U-10Zr-7Nb alloys will change the phase that is from the αU phase to γU and the change the microstructure formed. The microstructural changes show that in the higher Nb content, the grains that are formed become finer.
KOMPOSISI, STRUKTUR DAN DENSITAS PADUAN U-7Mo-xSi Supardjo; Agoeng Kadarjono; Jan Setiawan; Ganisa Kurniati Suryaman
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 27 No. 2 (2021): Urania : Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2021.27.2.6386

Abstract

The structure of U-7Mo-xSi (x = 1, 2, and 3%) alloy was studied to obtain a new uranium alloy suitable for use as a candidate for high-density uranium research reactor fuel. The U-7Mo-xSi alloy was made by melting technique using an arc furnace. The characterization of the alloy includes chemical composition, density, and structural phases to identify the phases contained in the alloy. The hardness test was also done. The density characterization results show that U content and density of the alloy decrease with increasing of Si content in the U-7Mo-xSi alloy. On the other hand, the hardness of the alloy increases with increasing of Si content. The X-ray diffraction pattern of U-7Mo-xSi alloy was observed from diffraction angle of 25° to 95°. The results indicate the presence of U-γ, U3Si2, and U3Si2Mo phases. The higher the Si content, the more U3Si2 phase is formed and the more the hardness increases due to the formation of bonds between Si and Si.
PENGARUH MEDIA PENDINGIN TERHADAP KARAKTERISTIK MEKANIK DAN STRUKTUR MIKRO PADA PELAT BAJA KARBON RENDAH Iskandarsyah Wicaksono; Sri Ismarwanti; Jan Setiawan; Ferry Budhi Susetyo; Syamsuir
Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir Vol. 27 No. 1 (2021): Urania: Jurnal Ilmiah Daur Bahan Bakar Nuklir
Publisher : Badan Riset dan Inovasi Nasional

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17146/urania.2021.27.1.6187

Abstract

Low carbon steel has high ductility and is easy to shape, so it is widely used in industry and construction. However, this material has low mechanical strength and hardness, so it is easy to wear. Mechanical properties can be improved by heat treatment, namely heating at a specific temperature and holding it for some time and then cooling. Cooling media will affect the level of enhancement in its mechanical properties. Therefore, in this study, observations were done on the mechanical characteristics and microstructure of low carbon steel after heat treatment and cooling on various cooling media. The heating process was carried out at a temperature of 950 °C with a holding time of 15 minutes. The sample is then cooled with a variety of coolants (aqua dest, cooking oil, oil and open-door furnace). The results of the observations on samples of low carbon steel plates (0.0524%) shows that the sample without heat treatment has the highest stress value of 375.75 MPa and the open furnace door cooling has the lowest stress value of 200.53 MPa. The highest strain value occurred in the open-door cooling of 38.77% and the lowest strain value of 25.49% occurred in the cooling with cooking oil. Observation on the material's microstructure before and after heat treatment shows ferrite and pearlite.
Co-Authors . Futichah Abdurahman . Abdussalam Abdussalam, Abdussalam Agoeng Kadarjono Agoeng Kadarjono Agus Jamaludin . . Agus Kurniawan Agus Sujatno Agustino Zulys Aisah, Nuning Al Afghani, Fajar Ali, Nora'aini Andrean Andrean Andri Suherman Arbi Dimyati Ardianto, Donie Agus Arief Sasongko Adhi ARIF NUGROHO Aritonang, Sovian Aslina Br Ginting Bambang Soegijono Baskara, Hedy Aditya Bayquni, Bayquni BOYBUL BOYBUL Budianto, Dwi Dadang . . Deni Mustika Deni Mustika Djoko Hadi Prajitno Dwi Biyantoro Dwi Biyantoro Dwi Budianto Dwi Gustiono Dwi Gustiono, Dwi Dwi Nanto Dwi Nanto, Dwi Eddy Indarto Edy Sumarno Edy Sumarno Edy Sumarno, Edy Effendi, Mohammad Dachyar Elfirza Rosiana Erilia Yusnitha Erilia Yusnitha Erlina Noerpitasari Fajar Al Afghani Fatma Husaini Fatma Husaini Fauzi, Willy Pahmi Ferry Budhi Susetyo Ferry Budhi Susetyo Ferry Budhi Susetyo Fitri Yanti Fitriani, Mita Fitriani, Mitra Futichah . Ganisa Kurniati Suryaman Ganisa Kurniati Suryaman Gazali, Ria Guswardani Guswardani . Guswardani . . Guswardani Guswardani Guswardani Guswardani Hadi Prajitno, Djoko Hamdan Akbar Notonegoro Hamdan Akbar Notonegoro Hanifah Dwiyanti Hanifah Dwiyanti Harahap, Muslim Efendi Hedy Aditya Baskhara Heranudin Heranudin Heri Hardiyanti Heri Hardiyanti . . Hutagaol, Antonio Gogo Ihwanul Aziz Iis Haryati Ikhwanul Aziz Irawati Irawati Irawati Irawati Irvan Irvan Isfandi isfandi, Isfandi Iskandarsyah Wicaksono Iskandarsyah Wicaksono Iwantono Iwan Barnawi Juhana Juhana Kartikasari, Deasy Kiswanta Kusnadi, Heri M Husna Alhasa M. Husna Al Hasa Maman Kartaman Ajiriyanto Maman Kartaman Ajiriyanto Marfin Marfin Masripah Masripah Masripah Masripah Masrukan Masrukan Masrukan Masrukan Masrukan Masrukan Masrukan Masrukan Megawanti, Priarti Mirza Wibowo Mohammad Dachyar Effendi Muslim Efendi Harahap Ngatijo Ngatijo Ngatijo NONI DWI SARI Noni Dwi Sari Notonegoro, Hamdan Akbar Nuning Aisah Nurkahfi Irwansyah Nurtiyanto, Woro Agus Ojak Abdul Rozak Oky Supriadi Pambudi, Yoyok Dwi Setyo Pranjono . Putranto, Dwi Putri, Elvina Rahmiati Rahmiati Rahmiati Ramlan Ramlan Ramlan Ramlan Ramlan Ramlan, H. Ratih Langenati Ratih Langenati Ratih Langenati Ridwan . Riski Maulana, Riski Riwandi Sihombing Rizkynawan, Benridho Rohmad Sigit Rosiana, Elfirza Rosika Kriswarini SARI, NONI DWI Setia Permana Setia Permana Seto Roseno Seto Roseno Sigit . Sigit E.B.P., Rohmad Sigit, Rohmad Silviana Simbolon Simbolon, Silviana Siti Saleha Siti Saleha Slamet Pribadi Slamet Pribadi Slamet Pribadi . . Sofyan, Muhammad Azis Sri Galuh Banawa Sri Ismarwanti Sri Ismarwanti Sri Ismarwanti Sri Ismarwanti Sri Ismarwanti Sri Ismarwanti, Sri Sugeng Riyanto Sunardi Sunardi Sungkono Sungkono Sungkono Sungkono Sungkono Supardjo Supardjo Supardjo Suprijono . . Suryaman, Ganisa K Susetyo, Ferry Budhi Susworo . . Sutri Indaryati Sutri Indaryati Syamsuir Syamsuir Syamsuir Syamsul Fatimah Taufiq Al Farizi Tihera, Dinda Torowati Torowati Torowati Tri Yulianto Tri Yulianto Triarjo . Triyanto, Aripin Usman Sudjadi Utomo, Luki Wibowo, Mirza Woro Agus Nurtiyanto Yanlinastuti . Yanlinastuti Yanlinastuti Yatno Dwi Agus Susanto Yatno Dwi Agus Susanto, Yatno Dwi Agus Yohanes Edi Gunanto Yunasfi Yunasfi Yunasfi Yuniar Istiyawati Yunus, Muhamad Yasin Zulkarnain Zulkarnain