Garuda - Garba Rujukan Digital

Upaya Peramalan Cadangan Minyak Pada Sumur SBR-A Menggunakan Metode Decline Curve Analysis Sakinah; Firdaus; Joko Wiyono; Yudiaryono; Abdul Gafara Karim; Aliyah Sayyidina Putri Bahtiar; Darmiyati, Iin
AL-MIKRAJ Jurnal Studi Islam dan Humaniora (E-ISSN 2745-4584) Vol. 3 No. 2 (2023): Al-Mikraj, Jurnal Studi Islam dan Humaniora
Publisher : Pascasarjana Institut Agama Islam Sunan Giri Ponorogo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.37680/almikraj.v3i2.7160

Oil and natural gas are needs that are needed by every country including Indonesia. national need. In the SBR-A well field R, this was used for final project research, namely estimating oil reserves using the decline curve analysis method, the SBR-A well experienced a decrease in production. The purpose of carrying out the decline curve analysis method is to estimate or predict the estimated ultimate recovery and oil production in the future, so that we can predict the future production prospects of the field under study, so that we can determine the best steps taken to develop the field. either in actual conditions or other conditions. Based on the research results obtained from data processing using the Decline Curve Method, it can be seen that the type of curve is Exponential decline, with an actual cumulative value of 51328.40203 STB and a decline exponential value (b) of 0.01 and a nominal value of decline (D) of 0.007. And the remaining oil reserves (ERR) up to the economic limit of 53865.62128 STB, so that the SBR-A well can produce up to the economic limit of 5 BOPD, which is 674 days or 1.9 years, which starts production from 8 May 2023 to 1 January 2025. With the value of the amount of reserves that can be produced (EUR) in the SBR-A Well, which is 105194,023 STB..

Desain Electrical Submersible Pump (ESP) Untuk Meningkatkan Laju Alir Produksi Pada Sumur “DT014” Darmiyati, Iin; Della Endangtri; Firdaus; Rohima Sera Afifah; Abdul Gafar Karim; Fatma; Muhammad Alif; Pratama Bagus Restu.S
AL-MIKRAJ Jurnal Studi Islam dan Humaniora (E-ISSN 2745-4584) Vol. 3 No. 2 (2023): Al-Mikraj, Jurnal Studi Islam dan Humaniora
Publisher : Pascasarjana Institut Agama Islam Sunan Giri Ponorogo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.37680/almikraj.v3i2.7161

Oil production from a well often decreases due to reduced reservoir pressure, so a production increase method or artificial lift is needed to maintain or increase the production flow rate. One of the commonly used artificial lift methods is the Electrical Submersible Pump (ESP). This study aims to design an optimal ESP system for the DT014 well, which is experiencing decreased production. The analysis was carried out by considering reservoir parameters, fluid characteristics, and well operating conditions. The design process includes the selection of pumps, motors, and electrical cables that are in accordance with production needs. Simulations were carried out to ensure the performance of the ESP in increasing oil production efficiently and economically. The design results show that the application of ESP to the DT014 well can significantly increase the production flow rate compared to previous methods. By considering pump efficiency and energy consumption, the selection of the right ESP can maximize production while minimizing operational costs. Thus, the implementation of ESP has proven to be an effective solution to increase oil production in wells experiencing decreased reservoir pressure. This study is expected to be a reference for the optimization of artificial lift systems in oil fields with similar conditions.

RIG “AB-1” Specification Study on “Batara” Well Based on Drawworks, Hook Load and Mud Pump Data Nijusiho Manik; Rohima Sera Afifah; Andi Jumardi; Fatma; M. Rizal Faahrun; Zavta Rizki; Darmiyati, Iin
AL-MIKRAJ Jurnal Studi Islam dan Humaniora (E-ISSN 2745-4584) Vol. 4 No. 1 (2023): Al-Mikraj, Jurnal Studi Islam dan Humaniora
Publisher : Pascasarjana Institut Agama Islam Sunan Giri Ponorogo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.37680/almikraj.v4i1.7162

The analysis conducted in this study focuses on the "AB-1" rig's ability to handle calculated loads. Results show that at 1,248 ft MD with 13 3/8" casing, the hook load and drawworks are both 84,864 pounds. At 5,818 ft MD with 9.5/8" casing, these values increase to 273,446 pounds. At 8,463 ft MD using dual 3.1/2 tubing, the load is 159,748.8 pounds. Mud pump power calculations reveal pressures of 681,408 psi for surface sections and 5,632.97 psi for production sections. Casing is a steel pipe inserted into a wellbore to prevent wall collapse, isolate abnormal pressure zones, and provide space for subsurface equipment during hydrocarbon production. This study aims to evaluate the casing load by analyzing hook load, drawworks, and mud pump power. Hook load represents the weight supported by the rig, including the accumulation of pipe weight, casing weight, and drag forces. Drawworks serve as lifting equipment for casing and tubing during drilling operations, while mud pumps circulate drilling fluids to support the process. Based on these findings, the "AB-1" rig is deemed suitable for operations with a hook load and drawworks capacity of up to 500 tons (1,000,000 pounds) and a mud pump pressure limit of 5,787 psi.

Evaluasi Stimulasi Hydraulic Fracturing dan Kondisi Formasi Pada Reservoir Sandstone di Sumur AML-14 Darmiyati, Iin; Aulia Miranti Larasathi; Amiruddin; Firdaus; Sulardi; Hamriyani Ryka; Ipan Sampe
AL-MIKRAJ Jurnal Studi Islam dan Humaniora (E-ISSN 2745-4584) Vol. 2 No. 1 (2021): Studi Keislaman dan Humaniora
Publisher : Pascasarjana Institut Agama Islam Sunan Giri Ponorogo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.37680/almikraj.v2i1.7206

The reservoir layer in the FAY field is sandstone which is categorized as having low permeability. An evaluation was carried out on the AML-14 well to determine the cause of failure of the hydraulic fracturing work carried out on the well and its handlers The evaluation carried out in the FAY field included validating IPR data before hydraulic fracturing, pressure obtained during the step rate test, fracture geometry obtained after hydraulic fracturing, average permeability value, and increase in IPR value using the vogel method. Based on the results of the evaluation carried out, it can be seen that the pressure obtained during the step rate test was around 2602 Psi and the fracture flow rate was 1.2 Bpm which caused a screen out. The obtained fracture conductivity is about 6200 md-ft. The average permeability value obtained is 79 mD. The results of the fracturing carried out were that production decreased from the previous 154,626 Bopd to 15,757 Bopd. These results indicate that the hydraulic fracturing operation on the AML-14 well can be declared a failure due to a screen out that has an impact on production results that are not as expected. Handling of the well can be done by installing gravel pack conditions as well as slug pumping of sand which can effectively reduce the problem of placing sand into the wellbore.

Evaluasi Stimulasi Hydraulic Fracturing Dan Kondisi Formasi Pada Reservoir Sandstone Di Sumur AML-14 Aulia Miranti Larasathi; Amiruddin; Firdaus; Sulardi; Hamriyani Ryka; Ipan Sampe; Darmiyati, Iin
AL-MIKRAJ Jurnal Studi Islam dan Humaniora (E-ISSN 2745-4584) Vol. 2 No. 1 (2021): Studi Keislaman dan Humaniora
Publisher : Pascasarjana Institut Agama Islam Sunan Giri Ponorogo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.37680/almikraj.v2i1.7207

The reservoir layer in the FAY field is sandstone which is categorized as having low permeability. An evaluation was carried out on the AML-14 well to determine the cause of failure of the hydraulic fracturing work carried out on the well and its handlers The evaluation carried out in the FAY field included validating IPR data before hydraulic fracturing, pressure obtained during the step rate test, fracture geometry obtained after hydraulic fracturing, average permeability value, and increase in IPR value using the vogel method. Based on the results of the evaluation carried out, it can be seen that the pressure obtained during the step rate test was around 2602 Psi and the fracture flow rate was 1.2 Bpm which caused a screen out. The obtained fracture conductivity is about 6200 md-ft. The average permeability value obtained is 79 mD. The results of the fracturing carried out were that production decreased from the previous 154,626 Bopd to 15,757 Bopd. These results indicate that the hydraulic fracturing operation on the AML-14 well can be declared a failure due to a screen out that has an impact on production results that are not as expected. Handling of the well can be done by installing gravel pack conditions as well as slug pumping of sand which can effectively reduce the problem of placing sand into the wellbore.

Analisis Kecepatan Krisis Dan Kecepatan Rata Rata Lumpur Pemboran Pada Pengangkatan Serbuk Bor Cerriansyah Ramadhan; Andi Jumardi; Eltimeyansi Chrisye Randanan; Karmila; Joko Wiyono; Ipan Sampe; Darmiyati, Iin
AL-MIKRAJ Jurnal Studi Islam dan Humaniora (E-ISSN 2745-4584) Vol. 2 No. 2 (2022): Al-Mikraj, Jurnal Studi Islam dan Humaniora
Publisher : Pascasarjana Institut Agama Islam Sunan Giri Ponorogo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.37680/almikraj.v2i2.7208

As we know mud drilling provides many benefits in drilling operations. This needs to be considered also how the speed of the drilling mud is so in bringing drill powder above the surface so that there are no problems at will. The problem that occurs when the drill powder is not carried to the surface is the deposition at the bottom of the borehole. To see if the drilling sludge can circulate properly, it is necessary to calculate critical speed and average speed. Research data such as borehole diameter, mud weight, yield point, and plastic viscosity as well as data on each circuit component and annulus will be needed to determine flow patterns in circuits and annulus. Determination of flow patterns is also needed so that it can find out if the drilling sludge is functioning properly in the borehole. After doing calculations on the circuit then the vcDP result = 5.99 fps < V dp = 13.18 fps, VcMWD Tools = 6.28 < V MWD Tools = 26.82 fps, Vc3xDC = 6.62 fps < V 3xDC = 47.69 fps, Vc4xHWDP = 6.28 fps < V 4xHWDP = 26.82 fps, Vcjar = 6.28 fps < V jar = 26.82 fps, Vc16xHWDP = 6.76 fps < V 16xHWDP = 26.82 fps, then it is certain that the flow of mud in the circuit is turbulent so as to cause a cleaning effect on a fairly good circuit. In annulus obtained results VcaDP = 5.43 fps > V adp = 5.10 fps, VcaMWD Tools = 6.66 fps < Va MWD Tools = 10.38 fps, Vca3xDC = 6.10 fps < Va 3xDC = 8.05 fps, Vca 4xHWDP = 5.43 fps > Va 4xHWDP = 5.11 fps, Vcajar = 6.10 fps < Va jar = 8.05 fps, Vca16xHWDP = 5.43 fps > Va 16xHWDP = 5.11 fps, Looking at the results of calculations on annulus more average speed values then it can be ascertained that the flow of mud in annulus is turbulent.

Evaluation and Planning Of Acidizing Method to Resolve Scale Issues in Well "YDK-01," "Sandy" Field Wawan Andi’ Padang; M. Nur Mukmin; Rohima Sera; Bambang Wicaksono; Dharma Arung Laby; Darmiyati, Iin
AL-MIKRAJ Jurnal Studi Islam dan Humaniora (E-ISSN 2745-4584) Vol. 2 No. 2 (2022): Al-Mikraj, Jurnal Studi Islam dan Humaniora
Publisher : Pascasarjana Institut Agama Islam Sunan Giri Ponorogo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.37680/almikraj.v2i2.7209

The “YDK-01” well has alkaline Formation Water with a pH value of 8,3. Therefore, Scale can form in the productive zone so that over time, Scale will continue to settle and be difficult to solved. From several Acidizing methods, Matrix Acidizing is the most recommended because in the wells examined there are indications of a positive Skin value (Formation Damage). Matrix Acidizing is a Reservoir stimulation method used to overcome Formation Damage in the wells caused by Scale. In this research, it is done using manual calculations using (Stiff & Davis), (Skillman, McDonald & Stiff) and Inflow Performance Relationship Wiggins equations, which aims to evaluate the problem of Scale. Changes in well production rates can be seen from a comparison of several parameters before and after Acidizing such as: Inflow Performance Relationship curve, Permeability value, Productivity Index value, and Skin. In the “YDK-01” well, there was an increase in the Qomax value of 47.16 bopd. The Productivity Index value of oil which was previously 0.129 bopd/psia, has changed to 0.198 bopd/psia. Permeability value has increased by 12 md and Skin value has decreased by 28.54. Parameters above prove that the Matrix Acidizing method works well in overcome scale on the well.

Potensial of Lost Circulation Zones in RJ Well, CP Field by Calculating Hydrostatic, Formation and Fracture Pressure Reynaldy Julio; M. Nur Mukmin; Firdaus; Afrida; Aprilino Alfa Kurmasela; Darmiyati, Iin; Annisa Efidiawati
AL-MIKRAJ Jurnal Studi Islam dan Humaniora (E-ISSN 2745-4584) Vol. 2 No. 2 (2022): Al-Mikraj, Jurnal Studi Islam dan Humaniora
Publisher : Pascasarjana Institut Agama Islam Sunan Giri Ponorogo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.37680/almikraj.v2i2.7210

This study aims to analyze the potential of lost circulation zones in the RJ well at the CP field by calculating hydrostatic pressure, formation pressure, and formation fracture pressure. Lost circulation occurs when drilling fluid is lost into the formation, which can disrupt the drilling process. In this study, calculations were made for hydrostatic pressure, formation pressure, and formation fracture pressure at various depths of the well. The results show that at a depth of 741 ft, the hydrostatic pressure is 330.22 psi, formation pressure is 318.66 psi, and formation fracture pressure is 982.88 psi. Meanwhile, at a depth of 9517 ft, the hydrostatic pressure reaches 5438.78 psi, formation pressure is 5290.31 psi, and formation fracture pressure is 7237.24 psi. The significant difference between hydrostatic pressure and formation pressure leads to the occurrence of lost circulation. In conclusion, the potential for lost circulation in the RJ well is caused by hydrostatic pressure being higher than formation pressure. This study provides important insights into the factors influencing lost circulation and is expected to serve as a reference for future drilling operations.

Mitigation Of Loss Circulation Problems Using Calcium Carbonate In Well 'HF-05', 'Kanaan' Field Heldy Febryanto; Firdaus; Risna; , Abdul Gafar Karim; Aprilino Alfa Kurmasela; Darmiyati, Iin; Annisa Efidiawati
AL-MIKRAJ Jurnal Studi Islam dan Humaniora (E-ISSN 2745-4584) Vol. 2 No. 2 (2022): Al-Mikraj, Jurnal Studi Islam dan Humaniora
Publisher : Pascasarjana Institut Agama Islam Sunan Giri Ponorogo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.37680/almikraj.v2i2.7211

Lossicirculation isione of theiproblems thatioften occursiin theidrillingiworld where loss of circulation or loss of circulation of mud is interpreted as a loss of circulation in a small amount or all of the drilling mud when it is circulated, so that when the drilling takes place, the circulated mud enters the drilling zone. penetrated formation. The "HF-05" well in the "KANAAN" fieldiis aidevelopmentiwell thatiaimsito proveithe existenceiof oil and gas reserves in Sukra District, Indramayu Regency. The loss circulation problem that occurred in the "HF-05" well occurred at a depth of 1945 mMD, route with a total loss of 278 bbl with a mud weight of 1.19 sg. The methodology used in handling loss circulation is collecting the necessary data, calculating hydrostatic pressure (PH), calculating drilling hydraulics, and identifying the causes of loss circulation by comparing hydrostatik pressure (PH) with formation pressure. Then carry out countermeasures using loss circulation material (LCM) type Calcium Carbonat. The results of countermeasures for loss circulation using loss circulation material (LCM) type Calcium Carboante in the "HF-05" well were successful with hydrostatik pressure (PH) lower than formation pressure (PF).

Analisis Efisiensi Rasio Luas Dimensi Apda Separator C-3-08-A di Unit Hydrocracking Unibon Plant Herry Setiawan; Andi Jumardi; Rohima Sera Afifah; Irma Andrianti; Dharma Arung Laby; Ummul Haq; Darmiyati, Iin
AL-MIKRAJ Jurnal Studi Islam dan Humaniora (E-ISSN 2745-4584) Vol. 2 No. 2 (2022): Al-Mikraj, Jurnal Studi Islam dan Humaniora
Publisher : Pascasarjana Institut Agama Islam Sunan Giri Ponorogo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.37680/almikraj.v2i2.7342

This study aims to evaluate the performance of the C-3-08A separator used in a hydrocracking unit within an industrial processing facility, in support of increased production targets. The primary focus is to calculate and analyze the Area Ratio (Rm), which represents the ratio of the separator's length to its inlet diameter, ensuring efficiency in the fluid separation process at a flow rate of 13,435 BFPD. The method applied involves manual calculations to determine the Rm value and propose improvements to the separator design based on parameters such as length and flow rate. Analysis results show that the initial Rm value of 2.527 does not meet the standard requirement, which stipulates an Rm range between 3 and 5. Recalculation suggests that extending the separator length to 36 ft yields an Rm of 3.015, meeting the standard. Additionally, reducing the flow rate to 8,000 BFPD while maintaining a separator length of 30.183 ft and diameter of 10.045 ft produces an Rm of 3.004, also within acceptable limits. In conclusion, recalculating and adjusting the separator design parameters can enhance fluid separation efficiency and support increased production outcomes.

Title

Found 25 Documents
Search

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Title Search

Found 25 Documents Search

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Title

Found 25 Documents
Search