Claim Missing Document
Check
Articles

PERENCANAAN JARINGAN LTE FDD 1800 MHZ DI KOTA SEMARANG MENGGUNAKAN ATOLL Fauzi, Muhamad Ridwan; Setiyono, Sukiswo; Prakoso, Teguh
Transient: Jurnal Ilmiah Teknik Elektro TRANSIENT, VOL. 4, NO. 3, SEPTEMBER 2015
Publisher : Universitas Diponegoro

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (543.208 KB) | DOI: 10.14710/transient.4.3.517-524

Abstract

Abstrak LTE merupakan teknologi evolusi dari GSM yang dikembangkan oleh 3GPP dan disebut sebagai salah satu teknologi pra-generasi keempat (4G). Implementasi LTE di Indonesia sendiri masih belum menyuluruh dan baru diterapkan di beberapa kota besar saja, namun frekuensi untuk menggelar LTE sudah disediakan, salah satunya pada frekuensi 1800 MHz. Sebelum menggelar teknologi LTE perlu dilakukan perencanaan jaringan untuk mengetahui jumlah eNodeB yang dibutuhkan. Pada Tugas Akhir ini dilakukan perencanaan jaringan LTE FDD 1800 MHz menggunakan perangkat lunak Atoll. Perencanaan yang dilakukan menggunakan metode perencanaan cakupan dengan studi kasus di Kota Semarang. Untuk mendukung hal tersebut ditentukan model propagasi yang sesuai untuk perencanaan ini, yaitu model COST-231 Hata. Hasil dari simulasi menunjukkan bahwa jumlah eNodeB yang dibutuhkan dalam perencanaan adalah sebanyak 152 site dan 453 sel agar area Kota Semarang tercakupi oleh RS dan SINR minimal sekurang-kurangnya 95%. Hasil lain didapatkan bahwa jumlah pelanggan yang dapat mengakses jaringan hingga ke daerah indoor didapatkan sebanyak 98,7% untuk bandwidth 5 MHz, 97,1% untuk 10 MHz, 95,9% untuk 15 MHz, dan 94,8% untuk 20 MHz. Pada bandwidth 20 MHz kapasitas sel dan throughput sel yang dihasilkan adalah yang paling besar dengan beban sel sebesar 50,53% untuk downlink dan 18,84% untuk uplink, dan throughput sel yang dihasilkan sebesar 34.633 kbps untuk downlink dan 9.591 kbps untuk uplink. Kata kunci: LTE, perencanaan cakupan,  Atoll  Abstract LTE is technology evolution of GSM that developed by 3GPP as one the 4G technology. LTE technology in Indonesia is not implemented entirely and just implemented in some big cities, however the frequencies for implementing this technology is available, one of them is 1800 MHz. It is necessary for network planning before deploying LTE to know the number of eNodeB. This final project discusses about LTE FDD network planning for 1800 MHz using software Atoll. This planning uses coverage planning method with case study in Semarang City. The propagation models that suitable to support this planning is COST-231 Hata model. The result of this simulation shows that the number of eNodeB that required in this planning is 152 site and 453 cell to result minimum RS and SINR coverage at least 95% of Semarang City area. The other result is that the number of user that connected to the network including indoor user is 98,7% for bandwidth 5 MHz, 97,1% for 10 MHz, 95,9% for 15 MHz, and 94,8% for 20 MHz. Bandwidth 20 MHz has the largest capacity cell and highest throughput cell with 50,53% cell load for downlink and 18,84% for uplink, and the throughput cell is 34.633 kbps for downlink dan 9.591 kbps for uplink. Keywords:  LTE, coverage planning, Atoll
PERANCANGAN ANTENA MONOPOL CETAK UNTUK KOMUNIKASI ULTRA WIDEBAND DENGAN ANALISIS MODE KARAKTERISTIK Damayanti, Denti Agustina; Prakoso, Teguh; Sofwan, Aghus
Transient: Jurnal Ilmiah Teknik Elektro TRANSIENT, VOL. 7, NO. 1, MARET 2018
Publisher : Universitas Diponegoro

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1452.526 KB) | DOI: 10.14710/transient.7.1.20-27

Abstract

UWB (Ultra Wideband) adalah sistem komunikasi jarak pendek yang mempunyai bandwidth yang sangat lebar beroperasi pada frekuensi 3,1-10,6 GHz. Dengan bandwidth operasi UWB yang besar maka diperlukan suatu antena dengan bandwidth yang besar pula, salah satu pendekatan untuk memperlebar bandwidth antena adalah dengan menggunakan Theory Characteristic Mode (TCM). Perancangan antena monopol cetak pada frekuensi kerja 3,1-10,6 GHz menggunakan bahan FR-4 dengan ketebalan 1,575 mm, dan konstanta dielektrik sebesar 4,3. Simulasi pancaran gelombang elektromagnetik menggunakan perangkat lunak CST Studio Suite 2016.  Dari hasil simulasi, antena monopol cetak mempunyai bandwidth 8,4 GHz dengan rentang frekuensi 2,5 – 10,9 GHz. Pada hasil simulasi frekuensi 3,1 GHz, 5 GHz, dan 10,6 GHz yang diperoleh nilai return loss kurang dari -10 dan VSWR sudah kurang dari 2, serta nilai gain lebih dari 2 dB dengan pola radisi omnidirectional. Hasil pengukuran antena monopol cetak mempunyai bandwidth 7,735 GHz dengan rentang frekuensi 3,18-10,915 GHz. Pada hasil pengukuran frekuensi 3,1 GHz, 5 GHz, dan 10,6 GHz yang diperoleh nilai return loss kurang dari -10 dan VSWR sudah kurang dari 2, serta nilai gain sebesar 3,27  dB dengan pola radisi omnidirectional. Antena tersebut telah memenuhi spesifikasi komunikasi ultra wideband.
PENGENALAN WAJAH MENGGUNAKAN LOCAL BINARY PATTERN (LBP) DAN SUPPORT VECTOR MACHINE (SVM) Mujib, Khusnil; Hidayatno, Achmad; Prakoso, Teguh
Transient: Jurnal Ilmiah Teknik Elektro TRANSIENT, VOL. 7, NO. 1, MARET 2018
Publisher : Universitas Diponegoro

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (830.195 KB) | DOI: 10.14710/transient.7.1.123-130

Abstract

Terdapat banyak metode yang digunakan untuk mengenali identitas seseorang, misalkan nomor unik, kartu identitas dan sandi rahasia. Kekurangan metode-metode tersebut antara lain, kartu dapat hilang, nomor unik dan sandi rahasia dapat terlupakan. Salah satu solusi untuk masalah ini adalah sistem identifikasi seseorang berdasarkan metode biometrik jenis fisiologis. Penelitian ini merancang sebuah sistem untuk mengidentifikasi wajah. Citra wajah diambil menggunakan kamera web kemudian diekstraksi cirinya dengan metode local binary pattern (LBP). Ciri wajah yang diperoleh diklasifikasi menggunakan support vector machine (SVM). Model terbaik SVM dibangun berdasarkan validasi silang grid search. Kernel linier terbaik dibentuk dengan   dan parameter . Kernel radial basis function (RBF) terbaik dicapai dengan   dan parameter  dan .  Berdasarkan pengujian terhadap keseluruhan citra wajah, akurasi kedua kernel adalah 96,0%. Pada pengujian lima ekspresi wajah dengan SVM kernel linier, akurasi 100,0% diperoleh untuk ekspresi sedih, netral dan mata tertutup. Sedangkan SVM kernel RBF menghasilkan akurasi 100,0% untuk ekspresi terkejut, netral dan mata tertutup. Hasil pengujian tersebut menunjukkan sistem pengenalan wajah yang dirancang telah berfungsi baik.
KARYA SASTRA PEREMPUAN: ANALISIS AWAL TENTANG PERANG GENDER Prakoso, Teguh; Khasanah, Venus
ATAVISME Vol 12, No 1 (2009): ATAVISME, Edisi Juni 2009
Publisher : Balai Bahasa Jawa Timur

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24257/atavisme.v12i1.159.77-82

Abstract

Tujuan artikel ini adalah menjelaskan perang gender yang tercermin dalam novel karya pengarang- pengarang perempuan Indonesia dari generasi Ayu Utami. Perang gender adalah ?dendam abadi? pengarang-pengarang perempuan terhadap pengarang laki-laki yang, sampai sekarang, mengeksploitasi tubuh perempuan dengan besar-besaran dan memaksa mereka untuk membaca tubuhnya sendiri dari sudut pandang laki-laki. Melalui teks erotis sebagai bahasa ekspresi, pengarang perempuan mampu menulis tubuh mereka dengan sudut pandangnya sendiri. Abstract: This paper has the objective of explaining the gender struggle implied in the novels of Indonesian female authors of Ayu Utami generation. The gender struggle is female author?s ?eternal enmity? towards male authors who, up till now, have greatly exploited woman?s body and force them to read their own body from the male point of view. Through erotic texts as the language of expression, female authors are able to write their body with their own point of view. Keywords: gender struggle, female authors, Ayu Utami generation
Bandwidth Improvement on Rectangular Monopole Antenna using Dual Bevel Technique for Ultrawideband Technology Liya Yusrina Sabila; Damayanti, Denti Agustina; Prakoso, Teguh
Mobile and Forensics Vol. 4 No. 1 (2022)
Publisher : Universitas Ahmad Dahlan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12928/mf.v4i1.5496

Abstract

This paper presents the analyzed Monopole Antenna for Ultrawideband with a rectangular patch design using bevel technique at a frequency of 3.1 – 10.6 GHz. The fabricated antennas with dual bevel angles have a very compact width and length of 40 mm x 33 mm respectively and a groundplane width of 13 mm. To get bandwidth improvement on monopole antennas can be applied to the bevel angle on the patch. So, to get the best antenna design, 3 optimizations of antenna size changes were carried out during the simulation, that is optimization of patch length, patch width and bevel angle. Variation of patch length and width is used to change the frequency range and variation of bevel angle to increase bandwidth. From each change, the best result is taken. The experiment obtained the best simulation result of antenna and then fabricate it. From the measurement results on the fabricated antenna, the lowest S11 value is -24.6 dB, gain 2.6 dBi at a frequency of 5 GHz and radiation pattern is omnidirectional. The optimization process using the bevel technique has been proven to be successful in shifting the frequency range by around 600 MHz and increasing the bandwidth by about 4% or 30 MHz.
Impedance Mathing Improvement of Half-Cut Broadband Printed Monopole Antenna with Microstrip Feeding Teguh Prakoso; Mochammad Facta; Razali Ngah; Tharek A. Rahman
International Journal of Electrical and Computer Engineering (IJECE) Vol 3, No 5: October 2013
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (313.557 KB)

Abstract

The requirement of wireless access networks and user equipments to support coexistence of many communication standards and frequency bands poses challenge on antenna to be broadband and small. The application of half-cut technique to broadband printed monopole with microstrip feeding worsens the resulted antenna’s impedance. To improve the half-cut antenna impedance mathing, two methods were investigated in this paper: (1) monopole and ground extension, (2) the application of microstrip line transformer and ground extension. The first approach only produces limited improvement, whereas method #2 can enhance the return loss significantly. The application of the second approach potentially produces antenna pair that has low mutual coupling, good return loss, and small size. Considering its radiation pattern, the antenna is suitable for diversity and MIMO. Its application in broadband microwave-photonic access point need special arrangement due to radiation null at 5 GHz band at right side.DOI:http://dx.doi.org/10.11591/ijece.v3i5.3376
Influence of Gate Material and Process on Junctionless FET Subthreshold Performance Munawar A Riyadi; Irawan D Sukawati; Teguh Prakoso; Darjat Darjat
International Journal of Electrical and Computer Engineering (IJECE) Vol 6, No 2: April 2016
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (205.183 KB) | DOI: 10.11591/ijece.v6i2.pp895-900

Abstract

The recent progress of dimension scaling of electronic device into nano scale has motivated the invention of alternative materials and structures. One new device that shows great potential to prolong the scaling is junctionless FET (JLFET). In contrast to conventional MOSFETs, JLFET does not require steep junction for source and drain. The device processing directly influence the performance, therefore it is crucial to understand the role of gate processing in JLFET. This paper investigates the influence of gate material and process on subthreshold performance of junctionless FET, by comparing four sets of gate properties and process techniques. The result shows that in terms of subthreshold slope, JLFET approaches near ideal value of 60 mV/decade, which is superior than the SOI FET for similar doping rate. On the other hand, the threshold value shows different tendencies between those types of device.
Non-Planar MOSFET Modeling with Analytical Approach Munawar A Riyadi; Darjat Darjat; Teguh Prakoso; Jatmiko E. Suseno
TELKOMNIKA (Telecommunication Computing Electronics and Control) Vol 12, No 4: December 2014
Publisher : Universitas Ahmad Dahlan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12928/telkomnika.v12i4.506

Abstract

Non-planar structures have been identified as promising structure for next device generation in the nanoelectronic era. However, the continuous device dimension scaling into nano regime eventually requires more sophisticated model due to the limitation of the existing models. A model for non-planar MOSFET structure was elaborated in this paper, especially for device with pillar structure, using analytical approach. The concern of channel shape and structure were discussed as well. The result shows the shift in subthreshold characteristic in the channel with recessed channel model. The charge sharing is suspected as one of the key parameter in the shift of performance in the recessed region.
Study on the Analytical Model of non-planar MOSFET Munawar A. Riyadi; Darjat .; Teguh Prakoso; Jatmiko E. Suseno
Proceeding of the Electrical Engineering Computer Science and Informatics Vol 1: EECSI 2014
Publisher : IAES Indonesia Section

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (897.77 KB) | DOI: 10.11591/eecsi.v1.411

Abstract

In the recent development of MOSFET, non-planar structure has been identified as promising structure for next device generation. The advanced scaling of device implies that more sophisticated model is required due to the limitation of the existing models for application in nano scale. Analytical model for non-planar MOSFET model is discussed in this paper, especially for device with pillar. The concern of channel shape and structure is elaborated as well. The result shows the shift in subthreshold characteristic due to the presence of recessed region in the channel with the simulated model.
A Broadband MIMO Antenna for Access Network Teguh Prakoso; N Shazwani M. Noor; E. H. Hadyan; M. A. Riyadi; Razali Ngah
Proceeding of the Electrical Engineering Computer Science and Informatics Vol 2: EECSI 2015
Publisher : IAES Indonesia Section

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (445.493 KB) | DOI: 10.11591/eecsi.v2.812

Abstract

This paper presents a compact and broadband MIMO antenna intended for wireless access network at 1.7 – 6.0 GHz. Impedance degradation introduced by half-cut technique is solved by inserting microstrip-line transformer.
Co-Authors Abdul Hamid Alfauzi Achmad Hidayatno Adhi Nugraha Affandi, Muhammad Afif Afin M Nurtsani Aghus Sofwan Agnes Yora Gracia Simatupang Ahmad Riyandi Ahmad Zaki Mubarok, Ahmad Zaki Akbar Satria Wardhana, Akbar Satria Alfian Rokhmansyah Ananda, Refisa Andreansyah, Muhammad Iqbal Apriani, Zuliana Apriliani Nabila Anjani Apriliani, Rina Ardhian Ainul Yaqin Arif Munandar Arifianto, Eko arjang Badriyah, Ratu Baron Murianda Brilian Dermawan Brillianing Pratiwi Damayanti, Denti Agustina Darjat Darjat Dewi, Arkidianabela Anggara Donny Dharmawan Dwi Budi Srisulistiowati E. H. Hadyan E.H. Hadyan E.H. Hadyan, E.H. Hadyan Eko Arifianto Eko Arifianto Enang Rusyana Enggar Hindami Hadyan Erasma, Erasma Fitra Jaya Hadyan, E. H. Halim, Indra Hanardi Satrio Hari Kurnia Safitri Heriani Heriani, Heriani Houtman Ian Amri Dinina Ibrahim Ibrahim Ifki Arifatul Utami Irawan D Sukawati Irawan Dharma Sukawati, Irawan Dharma Jatmiko E. Suseno Jatmiko E. Suseno Khoerul Fajri Lase, Sepandil Laras Liya Yusrina Sabila M. A. Riyadi M. Noor, N Shazwani M.A. Riyadi M.A. Riyadi, M.A. Riyadi Maulina, Murni Memet CASMAT Mertua Agung Durya, Ngurah Pandji Mochammad Facta Mohamad Yunus, Mohamad Muhamad Ridwan Fauzi, Muhamad Ridwan Mujib, Khusnil Munawar A Riyadi Munawar Agus Riyadi Murianti, Diana Mustari Mustari Muthia Nur Fajrina Muthouwali, Achmad Ngaqib N Shazwani M. Noor N. Shazwani M. Noor, N. Shazwani natanael pandapotan, natanael Ngah, Razali Ngah, Razali Nicholas Audric Adriel Nilawati Nilawati Novita Sari Harianja Nursantoso, Teguh Oktavianto, Tedi Permanasari, Devi Rachmani, Ferlinda Ainur Rahma Dewi Hartati Razali Ngah Razali Ngah Razali Ngah Riyadi, M. A. Riyadi, Munawar Riyadi, Munawar Riyadi, Munawar A. Riyandi, Ahmad Rovandi, Harris Rustaman, Dede Sabila, Liya Yusrina Santoso, Imam Santoso, Muhammad Hery Sapto Budi Priyatno Setiawan, Budhy Siti Aisyah Siti Hadianti, Siti Sofwan, Aghus Soleh, Soleh Stefani Dian Hutami Sudarmanto, Eko Sukiswo Sukiswo Sukiswo Sukiswo Sumardi . Suseno, Jatmiko E. Syafruddin Syuja Rizqullah Tanzila Azizi Rochim Tharek A. Rahman Ucu Rahayu Uli Wildan Nuryanto Utiarahman, Nurnaningsih Venus Khasanah Victor Pattiasina Winasis, Ganjar Yohandri Natan Yuli Christyono Yuli Christyono Yuliana, Rachma Yulistina Yulistina